View ST7MDT2-DVP2_4272813.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8-bit MCU for automotive with single voltage Flash/ROM memory, ADC, 16-bit timers, SPI, SCI interfaces

Memories - 8 or 16 Kbyte Program memory (ROM or single voltage Flash) with readout protection and in-situ programming (remote ISP) - 256 bytes EEPROM Data memory (with readout protection option in ROM devices) - 384 or 512 bytes RAM Clock, Reset and Supply Management - Enhanced reset system - Enhanced low voltage supply supervisor with 3 programmable levels - Clock sources: crystal/ceramic resonator oscillators or RC oscillators, external clock, backup Clock Security System - 4 Power Saving Modes: Halt, Active Halt, Wait and Slow - Beep and clock-out capabilities Interrupt Management - 10 interrupt vectors plus TRAP and RESET - 15 external interrupt lines (4 vectors) 44 or 32 I/O Ports - 44 or 32 multifunctional bidirectional I/O lines: - 21 or 19 alternate function lines - 12 or 8 high sink outputs 4 Timers - Configurable watchdog timer - Real-time base - Two 16-bit timers with: 2 input captures (only one on timer A), 2 output compares (only one on timer A), External clock input on timer A, PWM and Pulse generator modes
TQFP64 14 x 14
TQFP44 10 x 10

2 Communications Interfaces - SPI synchronous serial interface - SCI asynchronous serial interface (LIN compatible) 1 Analog Peripheral - 8-bit ADC with 8 input channels (6 only on ST72334Jx, not available on ST72124J2) Instruction Set - 8-bit data manipulation - 63 basic instructions - 17 main addressing modes - 8 x 8 unsigned multiply instruction - True bit manipulation Development Tools - Full hardware/software development package
Device Summary
Features Prog. memory RAM (stack) EEPROM Peripherals Oper. Supply CPU Freq. Oper. Temp. Packages ST72124J2 ST72314J2 ST72314J4 ST72314N2 ST72314N4 ST72334J2 ST72334J4 ST72334N2 ST72334N4 -Auto -Auto -Auto -Auto -Auto -Auto -Auto -Auto -Auto 8 Kbytes 16 Kbytes 8 Kbytes 16 Kbytes 8 Kbytes 16 Kbytes 8 Kbytes 16 Kbytes Flash/ROM 512 (256) 384 (256) 512 (256) 384 (256) 512 (256) 384 (256) 512 (256) 384 (256) bytes bytes bytes bytes bytes bytes bytes bytes 256 bytes Watchdog, Two 16-bit Timers, SPI, SCI ADC 3.2V to 5.5 V Up to 8 MHz (with up to 16 MHz oscillator) -40C to +85C / -40C to +125C Flash or ROM (-40C to +105C ROM only) TQFP44 TQFP64 TQFP44 TQFP64
Rev. 1
October 2007 1/150
1
Table of Contents
1 PREAMBLE: ST72C334-Auto VERSUS ST72E331 SPECIFICATION . . . . . . . . . . . . . . . . . . . . 7 2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 REGISTER AND MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 FLASH PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.2 5.3 5.4 5.5 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 STRUCTURAL ORGANIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 IN-SITU PROGRAMMING (ISP) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 MEMORY READOUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 DATA EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.2 6.3 6.4 6.5 6.6 6.7 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 MEMORY ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 ACCESS ERROR HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 READOUT PROTECTION OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.2 7.3 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8 SUPPLY, RESET AND CLOCK MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 8.1 LOW VOLTAGE DETECTOR (LVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 8.2 RESET SEQUENCE MANAGER (RSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 28 29 29 29 30 32 32 32 32 33 8.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2.2 Asynchronous External RESET Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2.3 Internal Low Voltage Detection RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2.4 Internal Watchdog RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 MULTI-OSCILLATOR (MO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 8.4.1 Clock Filter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.2 Safe Oscillator Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.3 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 SUPPLY, RESET AND CLOCK REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . .
CLOCK SECURITY SYSTEM (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 9.1 NON-MASKABLE SOFTWARE INTERRUPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 9.2 9.3 EXTERNAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 PERIPHERAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
10 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 10.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150. 36 ... 10.2 SLOW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2/150
2
Table of Contents
10.3 WAIT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 10.4 ACTIVE HALT AND HALT MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 10.4.1Active Halt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.2Halt Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2.1Input Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2.2Output Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2.3Alternate Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 I/O PORT IMPLEMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 39 40 40 40 40 40 43
11.2 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
11.4 LOW POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 11.5 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 11.5.1Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 12 MISCELLANEOUS REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 12.1 I/O PORT INTERRUPT SENSITIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 12.2 I/O PORT ALTERNATE FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 12.3 REGISTERS DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 13 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 13.1 WATCHDOG TIMER (WDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 13.1.1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.2Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.3Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.4Hardware Watchdog Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.5Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.6Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.7Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2 MAIN CLOCK CONTROLLER WITH REAL-TIME CLOCK TIMER (MCC/RTC) . . . . . . . 13.2.1Programmable CPU clock prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.2Clock-out capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.3Real-time clock timer (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.4Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.5Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 16-BIT TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.2Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.3Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.4Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.5Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.6Summary of Timer modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.7Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.4Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 50 50 51 51 51 51 53 53 53 53 54 54 55 55 55 55 67 67 67 68 73 73 73 73 75
3/150
3
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13.4.5Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.6Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.7Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 SERIAL COMMUNICATIONS INTERFACE (SCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.2Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.3General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.4LIN Protocol support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.5Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.6Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.7Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.8Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 8-BIT A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82 82 83 86 86 86 86 86 88 93 93 94 98
13.6.1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 13.6.2Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 13.6.3Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 13.6.4Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 13.6.5Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 13.6.6Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 14 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 14.1 ST7 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 14.1.1Inherent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1.2Immediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1.3Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1.4Indexed (No Offset, Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1.5Indirect (Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1.6Indirect Indexed (Short, Long) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1.7Relative Mode (Direct, Indirect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2 INSTRUCTION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 103 103 103 103 104 104 105
15 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 15.1 PARAMETER CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 15.1.1Minimum and Maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.2Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.3Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.4Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.1.5Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2.1Voltage Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2.2Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2.3Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.3 OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 108 108 108 108 109 109 109 110 111
15.3.1General Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 15.3.2Operating Conditions with Low Voltage Detector (LVD) . . . . . . . . . . . . . . . . . . . . 112 15.4 SUPPLY CURRENT CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 15.4.1Run and Slow Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 15.4.2Wait and Slow Wait Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 15.4.3Halt and Active Halt Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
4/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.4.4Supply and Clock Managers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 15.4.5On-Chip Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 15.5 CLOCK AND TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 15.5.1General Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5.2External Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5.3Crystal and Ceramic Resonator Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5.4RC Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5.5Clock Security System (CSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6 MEMORY CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6.1RAM and Hardware Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6.2EEPROM Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6.3Flash Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 EMC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7.1Functional EMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7.2Absolute Electrical Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7.3ESD Pin Protection Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.8 I/O PORT PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 117 118 121 122 123 123 123 123 124 124 125 127 129
15.8.1General Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 15.8.2Output Driving Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 15.9 CONTROL PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 15.9.1Asynchronous RESET Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 15.9.2ISPSEL Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 15.10 TIMER PERIPHERAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 15.10.1Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 15.10.216-Bit Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 15.11 COMMUNICATION INTERFACE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . 136 15.11.1SPI - Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 15.11.2SCI - Serial Communications Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 15.12 8-BIT ADC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 16 PACKAGE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 16.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 16.2 THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 16.3 ECOPACK(R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 17 DEVICE CONFIGURATION AND ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 143 17.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 17.2 OPTION BYTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 17.2.1User Option Byte 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 17.2.2User Option Byte 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 17.3 TRANSFER OF CUSTOMER CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 17.4 DEVELOPMENT TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 17.4.1Suggested List of Socket Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 17.5 ST7 APPLICATION NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 18 IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 18.1 SCI BAUD RATE REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 19 SUMMARY OF CHANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
5/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
To obtain the most recent version of this datasheet, please check at www.st.com>products>technical literature>datasheet. Please also pay special attention to the Section "IMPORTANT NOTES" on page 148
6/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
1 PREAMBLE: ST72C334-Auto VERSUS ST72E331 SPECIFICATION
New Features available on the ST72C334-Auto 8 or 16K Flash/ROM with In-Situ Programming and Readout protection New ADC with a better accuracy and conversion time New configurable Clock, Reset and Supply system New power saving mode with real-time base: Active Halt Beep capability on PF1 New interrupt source: Clock security system (CSS) or Main clock controller (MCC) ST72C334-Auto I/O Configuration and Pinout Same pinout as ST72E331 PA6 and PA7 are true open drain I/O ports without pull-up (same as ST72E331) PA3, PB3, PB4 and PF2 have no pull-up configuration (all I/Os present on TQFP44) PA5:4, PC3:2, PE7:4 and PF7:6 have high sink capabilities (20mA on N-buffer, 2mA on P-buffer and pull-up). On the ST72E331, all these pads (except PA5:4) were 2mA push-pull pads without high sink capabilities. PA4 and PA5 were 20mA true open drains. New Memory Locations in ST72C334-Auto 20h: MISCR register becomes MISCR1 register (naming change) 29h: new control/status register for the MCC module 2Bh: new control/status register for the Clock, Reset and Supply control. This register replaces the WDGSR register keeping the WDOGF flag compatibility. 40h: new MISCR2 register
7/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
2 INTRODUCTION
The ST72334J/N-Auto, ST72314J/N-Auto and ST72124J-Auto devices are members of the ST7 microcontroller family. They can be grouped as follows: - ST72334J/N-Auto devices are designed for midrange applications with Data EEPROM, ADC, SPI and SCI interface capabilities. - ST72314J/N-Auto devices target the same range of applications but without Data EEPROM. - ST72124J-Auto devices are for applications that do not need Data EEPROM and the ADC peripheral. All devices are based on a common industrystandard 8-bit core, featuring an enhanced instruction set. The ST72C334J/N-Auto, ST72C314J/N-Auto and ST72C124J-Auto versions feature single-voltage Figure 1. General Block Diagram
Flash memory with byte-by-byte In-Situ Programming (ISP) capability. Under software control, all devices can be placed in Wait, Slow, Active Halt or Halt mode, reducing power consumption when the application is in idle or standby state. The enhanced instruction set and addressing modes of the ST7 offer both power and flexibility to software developers, enabling the design of highly efficient and compact application code. In addition to standard 8-bit data management, all ST7 microcontrollers feature true bit manipulation, 8x8 unsigned multiplication and indirect addressing modes. For easy reference, all parametric data is located in Section 15 on page 108.
8-bit CORE ALU RESET ISPSEL VDD VSS OSC1 OSC2 CONTROL
PROGRAM MEMORY (8 or 16 Kbytes) RAM (384 or 512 bytes) EEPROM (256 bytes) ADDRESS AND DATA BUS
LVD MULTI-OSC + CLOCK FILTER MCC/RTC
PORT A PORT B PORT C TIMER B SPI PORT D 8-bit ADC
PA7:0 (8-bit for N versions) (5-bit for J versions) PB7:0 (8-bit for N versions) (5-bit for J versions)
PORT F PF7,6,4,2:0 (6-bit) TIMER A BEEP PORT E PE7:0 (6-bit for N versions) (2-bit for J versions) SCI
PC7:0 (8-bit)
WATCHDOG
PD7:0 (8-bit for N versions) (6-bit for J versions) VDDA VSSA
8/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
3 PIN DESCRIPTION
Figure 2. 64-Pin TQFP Package Pinout (N versions)
(HS) PE4 (HS) PE5 (HS) PE6 (HS) PE7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 AIN0 / PD0 AIN1 / PD1 AIN2 / PD2 AIN3 / PD3
64 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
NC NC PE1 / RDI PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 NC NC RESET ISPSEL PA7 (HS) PA6 (HS) PA5 (HS) PA4 (HS) 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 ei0 44 43 ei2 42 41 40 39 ei3 38 37 36 35 ei1 34 33 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
VSS_1 VDD_1 PA3 PA2 PA1 PA0 PC7 / SS PC6 / SCK / ISPCLK PC5 / MOSI PC4 / MISO / ISPDATA PC3 (HS) / ICAP1_B PC2 (HS) / ICAP2_B PC1 / OCMP1_B PC0 / OCMP2_B VSS_0 VDD_0
AIN4 / PD4 AIN5 / PD5 AIN6 / PD6 AIN7 / PD7 VDDA VSSA VDD_3 VSS_3 MCO / PF0 BEEP / PF1 PF2 NC OCMP1_A / PF4 NC ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 (HS) 20mA high sink capability eix associated external interrupt vector
9/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
PIN DESCRIPTION (Cont'd) Figure 3. 44-Pin TQFP Package Pinout (J versions)
PE1 / RDI PB0 PB1 PB2 PB3 PB4 AIN0 / PD0 AIN1 / PD1 AIN2 / PD2 AIN3 / PD3 AIN4 / PD4
44 43 42 41 40 39 38 37 36 35 34 1 33 2 32 3 31 ei0 ei2 4 30 5 29 ei3 6 28 7 27 8 26 9 25 ei1 10 24 11 23 12 13 14 15 16 17 18 19 20 21 22 AIN5 / PD5 VDDA VSSA MCO / PF0 BEEP / PF1 PF2 OCMP1_A / PF4 ICAP1_A / (HS) PF6 EXTCLK_A / (HS) PF7 VDD_0 VSS_0
PE0 / TDO VDD_2 OSC1 OSC2 VSS_2 RESET ISPSEL PA7 (HS) PA6 (HS) PA5 (HS) PA4 (HS)
VSS_1 VDD_1 PA3 PC7 / SS PC6 / SCK / ISPCLK PC5 / MOSI PC4 / MISO / ISPDATA PC3 (HS) / ICAP1_B PC2 (HS) / ICAP2_B PC1 / OCMP1_B PC0 / OCMP2_B
(HS) 20mA high sink capability eix associated external interrupt vector
10/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
PIN DESCRIPTION (Cont'd) For external pin connection guidelines, refer to Section 15 "ELECTRICAL CHARACTERISTICS" on page 108. Legend / Abbreviations for Table 1: Type: I = input, O = output, S = supply Input level: A = Dedicated analog input In/Output level: C = CMOS 0.3VDD/0.7VDD, CT= CMOS 0.3VDD/0.7VDD with input trigger Output level: HS = 20mA high sink (on N-buffer only) Port and control configuration: - Input: float = floating, wpu = weak pull-up, int = interrupt 1), ana = analog - Output: OD = open drain 2), PP = push-pull Refer to Section 11 "I/O PORTS" on page 40 for more details on the software configuration of the I/O ports. The RESET configuration of each pin is shown in bold. This configuration is valid as long as the device is in reset state. Table 1. Device Pin Description
Pin No. TQFP64 TQFP44 Pin Name Level Type Output Input Port Input float wpu ana int Main function Output (after reset) OD X X X X X X X X X X X X X X X X X X X X X X X X X X X X PP X X X X X X X X X X X X X X X X X X X X Port E4 Port E5 Port E6 Port E7 Port B0 Port B1 Port B2 Port B3 Port B4 Port B5 Port B6 Port B7 Port D0 Port D1 Port D2 Port D3 Port D4 Port D5 Port D6 Port D7 ADC Analog Input 0 ADC Analog Input 1 ADC Analog Input 2 ADC Analog Input 3 ADC Analog Input 4 ADC Analog Input 5 ADC Analog Input 6 ADC Analog Input 7
Alternate function
1 2 3 4
-
PE4 (HS) PE5 (HS) PE6 (HS) PE7 (HS)
I/O CT HS I/O CT HS I/O CT HS I/O CT HS I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O S S S CT CT CT CT CT CT CT CT CT CT CT CT CT CT CT CT
X X X X X X X X X X X X X X X X X X X X
X X X X ei2 ei2 ei2 ei2 ei3 ei3 ei3 ei3 X X X X X X X X
5 2 PB0 6 3 PB1 7 4 PB2 8 5 PB3 9 6 PB4 10 11 12 PB5 PB6 PB7
13 7 PD0/AIN0 14 8 PD1/AIN1 15 9 PD2/AIN2 16 10 PD3/AIN3 17 11 PD4/AIN4 18 12 PD5/AIN5 19 20 PD6/AIN6 PD7/AIN7
21 13 VDDA 22 14 VSSA 23 - VDD_3
Analog Power Supply Voltage Analog Ground Voltage Digital Main Supply Voltage
11/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
TQFP64
TQFP44
Type
Pin No. Pin Name
Level Output Input
Port Input float wpu ana int
OD
24 -
VSS_3
S I/O I/O I/O I/O CT CT CT CT X X X X X X X X X ei1 ei1 ei1 X X X X X X X X X X X X
PP
Main function Output (after reset)
Alternate function
Digital Ground Voltage Port F0 Port F1 Port F2 Port F4 Port F6 Port F7 Timer A Output Compare 1 Timer A Input Capture 1 Timer A External Clock Source Main clock output (fOSC/2) Beep signal output
25 15 PF0/MCO 26 16 PF1/BEEP 27 17 PF2 28 30 NC NC 29 18 PF4/OCMP1_A 31 19 PF6 (HS)/ICAP1_A
Not Connected Not Connected I/O CT HS
32 20 PF7 (HS)/EXTCLK_A I/O CT HS 33 21 VDD_0 S 34 22 VSS_0 35 23 PC0/OCMP2_B 36 24 PC1/OCMP1_B 37 25 PC2 (HS)/ICAP2_B 38 26 PC3 (HS)/ICAP1_B 39 27 PC4/MISO 40 28 PC5/MOSI 41 29 PC6/SCK 42 30 PC7/SS 43 44 45 PA0 PA1 PA2 S I/O I/O CT CT
Digital Main Supply Voltage Digital Ground Voltage X X X X X X X X X X X X X X X X X X X X ei0 ei0 ei0 ei0 X X X X X X X X X X X X X X X X X X X X X X X X Port C0 Port C1 Port C2 Port C3 Port C4 Port C5 Port C6 Port C7 Port A0 Port A1 Port A2 Port A3 Digital Main Supply Voltage Digital Ground Voltage X X X X X X X X T T X X Port A4 Port A5 Port A6 Port A7 Must be tied low in user mode. In programming mode when available, this pin acts as In-Situ Programming mode selection. Timer B Output Compare 2 Timer B Output Compare 1 Timer B Input Capture 2 Timer B Input Capture 1 SPI Master In / Slave Out Data SPI Master Out / Slave In Data SPI Serial Clock SPI Slave Select (active low)
I/O CT HS I/O CT HS I/O I/O I/O I/O I/O I/O I/O I/O S S I/O CT HS I/O CT HS I/O CT HS I/O CT HS I I/O C CT CT CT CT CT CT CT CT
46 31 PA3 47 32 VDD_1 48 33 VSS_1 49 34 PA4 (HS) 50 35 PA5 (HS) 51 36 PA6 (HS) 52 37 PA7 (HS) 53 38 ISPSEL 54 39 RESET 55 56 NC NC
X
X
Top priority non maskable interrupt (active low)
Not Connected S O I S Digital Ground Voltage Resonator oscillator inverter output or capacitor input for RC oscillator External clock input or Resonator oscillator inverter input or resistor input for RC oscillator Digital Main Supply Voltage
57 40 VSS_3 58 41 OSC2 3) 59 42 OSC1 3) 60 43 VDD_3
12/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
TQFP64
TQFP44
Type
Pin No. Pin Name
Level Output Input
Port Input float wpu ana int
OD
61 44 PE0/TDO 62 1 PE1/RDI 63 64 NC NC
I/O I/O
CT CT
X X
X X
X X
PP
Main function Output (after reset) X X Port E0 Port E1
Alternate function
SCI Transmit Data Out SCI Receive Data In
Not Connected
Notes: 1. In the interrupt input column, "eix" defines the associated external interrupt vector. If the weak pull-up column (wpu) is merged with the interrupt column (int), then the I/O configuration is pull-up interrupt input, else the configuration is floating interrupt input. 2. In the open drain output column, "T" defines a true open drain I/O (P-Buffer and protection diode to VDD are not implemented). See Section 11 "I/O PORTS" on page 40 and Section 15.8 "I/O PORT PIN CHARACTERISTICS" on page 129 for more details. 3. OSC1 and OSC2 pins connect a crystal or ceramic resonator, an external RC, or an external source to the on-chip oscillator see Section 3 "PIN DESCRIPTION" on page 9 and Section 15.5 "CLOCK AND TIMING CHARACTERISTICS" on page 117 for more details.
13/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
4 REGISTER AND MEMORY MAP
As shown in the Figure 4, the MCU is capable of addressing 64 Kbytes of memories and I/O registers. The available memory locations consist of 128 bytes of register locations, 384 or 512 bytes of RAM, up to 256 bytes of data EEPROM and 4 or 8 Kbytes of user program memory. The RAM Figure 4. Memory Map space includes up to 256 bytes for the stack from 0100h to 01FFh. The highest address bytes contain the user reset and interrupt vectors. IMPORTANT: Memory locations marked as "Reserved" must never be accessed. Accessing a reserved area can have unpredictable effects on the device.
0000h HW Registers (see Table 2) 007Fh 0080h 384 bytes RAM 01FFh 027Fh 0200h / 0280h Reserved 0BFFh 0C00h 0CFFh 0D00h BFFFh C000h E000h FFDFh FFE0h FFFFh 256 bytes Data EEPROM 512 bytes RAM
0080h 00FFh 0100h 01FFh
Short Addressing RAM Zero page (128 bytes) Stack or 16-bit Addressing RAM (256 bytes)
0080h 00FFh 0100h 01FFh Reserved 0200h 027Fh 8 Kbytes Program Memory 16 Kbytes Program Memory C000h
Short Addressing RAM Zero page (128 bytes) Stack or 16-bit Addressing RAM (256 bytes) 16-bit Addressing RAM
16 Kbytes E000h 8 Kbytes FFFFh
Interrupt and Reset Vectors (see Table 6 on page 35)
14/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
REGISTER AND MEMORY MAP (Cont'd) Table 2. Hardware Register Map
Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h to 001Fh 0020h 0021h 0022h 0023h 0024h to 0028h 0029h MCC MCCSR MISCR1 SPIDR SPICR SPISR PFDR PFDDR PFOR PDDR PDDDR PDOR PEDR PEDDR PEOR PBDR PBDDR PBOR PCDR PCDDR PCOR Block Register Label PADR PADDR PAOR Register Name Port A Data Register Port A Data Direction Register Port A Option Register Reserved Area (1 byte) Port C Data Register Port C Data Direction Register Port C Option Register Reserved Area (1 byte) Port B Data Register Port B Data Direction Register Port B Option Register Reserved Area (1 byte) Port E Data Register Port E Data Direction Register Port E Option Register Reserved Area (1 byte) Port D Data Register Port D Data Direction Register Port D Option Register Reserved Area (1 byte) Port F Data Register Port F Data Direction Register Port F Option Register 00h1) 00h 00h R/W R/W R/W 00h1) 00h 00h R/W R/W R/W 2) 00h1) 00h 00h R/W R/W R/W 2) 00h1) 00h 00h R/W R/W R/W 2) 00h1) 00h 00h R/W R/W R/W Reset Status 00h1) 00h 00h Remarks R/W R/W R/W 2)
Port A
Port C
Port B
Port E
Port D
Port F
Reserved Area (9 bytes)
Miscellaneous Register 1 SPI Data I/O Register SPI Control Register SPI Status Register
00h xxh 0xh 00h
R/W R/W R/W Read Only
SPI
Reserved Area (5 bytes)
Main Clock Control / Status Register
01h
R/W
15/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
Address 002Ah 002Bh 002Ch 002Dh 0030h 0031h 0032h 0033h 0034h 0035h 0036h 0037h 0038h 0039h 003Ah 003Bh 003Ch 003Dh 003Eh 003Fh 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h 0058h 006Fh
Block WATCHDOG
Register Label WDGCR CRSR
Register Name Watchdog Control Register
Reset Status 7Fh
Remarks R/W R/W R/W
Clock, Reset, Supply Control / Status Register 000x 000x Data-EEPROM Control/Status Register Reserved Area (4 bytes) 00h
Data-EEPROM EECSR
TIMER A
TACR2 TACR1 TASR TAIC1HR TAIC1LR TAOC1HR TAOC1LR TACHR TACLR TAACHR TAACLR TAIC2HR TAIC2LR TAOC2HR TAOC2LR MISCR2 TBCR2 TBCR1 TBSR TBIC1HR TBIC1LR TBOC1HR TBOC1LR TBCHR TBCLR TBACHR TBACLR TBIC2HR TBIC2LR TBOC2HR TBOC2LR SCISR SCIDR SCIBRR SCICR1 SCICR2 SCIERPR SCIETPR
Timer A Control Register 2 Timer A Control Register 1 Timer A Status Register Timer A Input Capture 1 High Register Timer A Input Capture 1 Low Register Timer A Output Compare 1 High Register Timer A Output Compare 1 Low Register Timer A Counter High Register Timer A Counter Low Register Timer A Alternate Counter High Register Timer A Alternate Counter Low Register Timer A Input Capture 2 High Register Timer A Input Capture 2 Low Register Timer A Output Compare 2 High Register Timer A Output Compare 2 Low Register Miscellaneous Register 2 Timer B Control Register 2 Timer B Control Register 1 Timer B Status Register Timer B Input Capture 1 High Register Timer B Input Capture 1 Low Register Timer B Output Compare 1 High Register Timer B Output Compare 1 Low Register Timer B Counter High Register Timer B Counter Low Register Timer B Alternate Counter High Register Timer B Alternate Counter Low Register Timer B Input Capture 2 High Register Timer B Input Capture 2 Low Register Timer B Output Compare 2 High Register Timer B Output Compare 2 Low Register SCI Status Register SCI Data Register SCI Baud Rate Register SCI Control Register 1 SCI Control Register 2 SCI Extended Receive Prescaler Register Reserved area SCI Extended Transmit Prescaler Register Reserved Area (24 bytes)
00h 00h xxh xxh xxh 80h 00h FFh FCh FFh FCh xxh xxh 80h 00h 00h 00h 00h xxh xxh xxh 80h 00h FFh FCh FFh FCh xxh xxh 80h 00h C0h xxh 00xx xxxx xxh 00h 00h --00h
R/W R/W Read Only Read Only Read Only R/W R/W Read Only Read Only Read Only Read Only Read Only 3) Read Only 3) R/W 3) R/W 3) R/W R/W R/W Read Only Read Only Read Only R/W R/W Read Only Read Only Read Only Read Only Read Only Read Only R/W R/W Read Only R/W R/W R/W R/W R/W R/W
TIMER B
SCI
16/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
Address 0070h 0071h 0072h to 007Fh
Block
Register Label ADCDR ADCCSR
Register Name Data Register Control/Status Register
Reset Status xxh 00h
Remarks Read Only R/W
ADC
Reserved Area (14 bytes)
Legend: x=undefined, R/W=read/write
Notes: 1. The contents of the I/O port DR registers are readable only in output configuration. In input configuration, the values of the I/O pins are returned instead of the DR register contents. 2. The bits corresponding to unavailable pins are forced to 1 by hardware, affecting accordingly the reset status value. These bits must always keep their reset value. 3. External pin not available.
17/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
5 FLASH PROGRAM MEMORY
5.1 INTRODUCTION Flash devices have a single voltage non-volatile Flash memory that may be programmed in-situ (or plugged in a programming tool) on a byte-by-byte basis. 5.2 MAIN FEATURES

Remote In-Situ Programming (ISP) mode Up to 16 bytes programmed in the same cycle MTP memory (Multiple Time Programmable) Readout memory protection against piracy
5.3 STRUCTURAL ORGANIZATION The Flash program memory is organized in a single 8-bit wide memory block which can be used for storing both code and data constants. The Flash program memory is mapped in the upper part of the ST7 addressing space and includes the reset and interrupt user vector area. 5.4 IN-SITU PROGRAMMING (ISP) MODE The Flash program memory can be programmed using Remote ISP mode. This ISP mode allows the contents of the ST7 program memory to be updated using a standard ST7 programming tools after the device is mounted on the application board. This feature can be implemented with a minimum number of added components and board area impact. An example Remote ISP hardware interface to the standard ST7 programming tool is described below. For more details on ISP programming, refer to the ST7 Programming Specification. Remote ISP Overview The Remote ISP mode is initiated by a specific sequence on the dedicated ISPSEL pin. The Remote ISP is performed in three steps: - Selection of the RAM execution mode - Download of Remote ISP code in RAM - Execution of Remote ISP code in RAM to program the user program into the Flash Remote ISP hardware configuration In Remote ISP mode, the ST7 has to be supplied with power (VDD and VSS) and a clock signal (oscillator and application crystal circuit for example).
This mode needs five signals (plus the VDD signal if necessary) to be connected to the programming tool. This signals are: - RESET: device reset - VSS: device ground power supply - ISPCLK: ISP output serial clock pin - ISPDATA: ISP input serial data pin - ISPSEL: Remote ISP mode selection. This pin must be connected to VSS on the application board through a pull-down resistor. If any of these pins are used for other purposes on the application, a serial resistor has to be implemented to avoid a conflict if the other device forces the signal level. Figure 5 shows a typical hardware interface to a standard ST7 programming tool. For more details on the pin locations, refer to the device pinout description. Figure 5. Typical Remote ISP Interface XTAL
HE10 CONNECTOR TYPE TO PROGRAMMING TOOL
1 CL0 CL1
OSC2
OSC1
VDD
ISPSEL 10K VSS RESET
ST7
ISPCLK ISPDATA 47K
APPLICATION
5.5 MEMORY READOUT PROTECTION The readout protection is enabled through an option bit. For Flash devices, when this option is selected, the program and data stored in the Flash memory are protected against readout piracy (including a re-write protection). When this protection option is removed the entire Flash program memory is first automatically erased. However, the EEPROM data memory (when available) can be protected only with ROM devices.
18/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
6 DATA EEPROM
6.1 INTRODUCTION The Electrically Erasable Programmable Read Only Memory can be used as a non-volatile backup for storing data. Using the EEPROM requires a basic access protocol described in this chapter. 6.2 MAIN FEATURES

Up to 16 bytes programmed in the same cycle EEPROM mono-voltage (charge pump) Chained erase and programming cycles Internal control of the global programming cycle duration End of programming cycle interrupt flag Wait mode management
Figure 6. EEPROM Block Diagram
EEPROM INTERRUPT
FALLING EDGE DETECTOR
HIGH VOLTAGE PUMP RESERVED EEPROM 0 IE LAT PGM
EECSR
0
0
0
0
ADDRESS DECODER
4
ROW DECODER
EEPROM MEMORY MATRIX (1 ROW = 16 x 8 BITS)
128 DATA MULTIPLEXER 4
128 16 x 8 BITS DATA LATCHES
4
ADDRESS BUS
DATA BUS
19/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
DATA EEPROM (Cont'd) 6.3 MEMORY ACCESS The Data EEPROM memory read/write access modes are controlled by the LAT bit of the EEPROM Control/Status register (EECSR). The flowchart in Figure 7 describes these different memory access modes. Read Operation (LAT=0) The EEPROM can be read as a normal ROM location when the LAT bit of the EECSR register is cleared. In a read cycle, the byte to be accessed is put on the data bus in less than 1 CPU clock cycle. This means that reading data from EEPROM takes the same time as reading data from EPROM, but this memory cannot be used to execute machine code. Write Operation (LAT=1) To access the write mode, the LAT bit has to be set by software (the PGM bit remains cleared). When a write access to the EEPROM area occurs, the value is latched inside the 16 data latches according to its address. Figure 7. Data EEPROM Programming Flowchart
READ MODE LAT=0 PGM=0 WRITE MODE LAT=1 PGM=0
When PGM bit is set by the software, all the previous bytes written in the data latches (up to 16) are programmed in the EEPROM cells. The effective high address (row) is determined by the last EEPROM write sequence. To avoid wrong programming, the user must take care that all the bytes written between two programming sequences have the same high address: only the four Least Significant Bits of the address can change. At the end of the programming cycle, the PGM and LAT bits are cleared simultaneously, and an interrupt is generated if the IE bit is set. The Data EEPROM interrupt request is cleared by hardware when the Data EEPROM interrupt vector is fetched. Note: Care should be taken during the programming cycle. Writing to the same memory location will over-program the memory (logical AND between the two write access data result) because the data latches are only cleared at the end of the programming cycle and by the falling edge of LAT bit. It is not possible to read the latched data. This note is illustrated by the Figure 8.
READ BYTES IN EEPROM AREA
WRITE UP TO 16 BYTES IN EEPROM AREA (with the same 11 MSB of the address)
START PROGRAMMING CYCLE LAT=1 PGM=1 (set by software)
INTERRUPT GENERATION IF IE=1 CLEARED BY HARDWARE
0
LAT
1
20/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
DATA EEPROM (Cont'd) 6.4 POWER SAVING MODES Wait mode The Data EEPROM can enter Wait mode on execution of the WFI instruction of the microcontroller. The Data EEPROM will immediately enter this mode if there is no programming in progress, otherwise the Data EEPROM will finish the cycle and then enter Wait mode. Halt mode The Data EEPROM immediately enters Halt mode if the microcontroller executes the HALT instruction. Therefore the EEPROM will stop the function in progress, and data may be corrupted. Figure 8. Data EEPROM Programming Cycle
READ OPERATION NOT POSSIBLE INTERNAL PROGRAMMING VOLTAGE ERASE CYCLE WRITE OF DATA LATCHES WRITE CYCLE READ OPERATION POSSIBLE
6.5 ACCESS ERROR HANDLING If a read access occurs while LAT=1, then the data bus will not be driven. If a write access occurs while LAT=0, then the data on the bus will not be latched. If a programming cycle is interrupted (by software/ RESET action), the memory data will not be guaranteed.
tPROG
LAT
PGM
EEPROM INTERRUPT
21/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
DATA EEPROM (Cont'd) 6.6 REGISTER DESCRIPTION CONTROL/STATUS REGISTER (CSR) Read / Write Reset Value: 0000 0000 (00h)
7 0 0 0 0 0 IE LAT 0 PGM
Bit 1 = LAT Latch Access Transfer This bit is set by software. It is cleared by hardware at the end of the programming cycle. It can only be cleared by software if PGM bit is cleared. 0: Read mode 1: Write mode Bit 0 = PGM Programming control and status This bit is set by software to begin the programming cycle. At the end of the programming cycle, this bit is cleared by hardware and an interrupt is generated if the ITE bit is set. 0: Programming finished or not yet started 1: Programming cycle is in progress Note: if the PGM bit is cleared during the programming cycle, the memory data is not guaranteed
Bit 7:3 = Reserved, forced by hardware to 0. Bit 2 = IE Interrupt enable This bit is set and cleared by software. It enables the Data EEPROM interrupt capability when the PGM bit is cleared by hardware. The interrupt request is automatically cleared when the software enters the interrupt routine. 0: Interrupt disabled 1: Interrupt enabled
Table 3. Data EEPROM Register Map and Reset Values
Address (Hex.) 002Ch Register Label EECSR Reset Value 7 6 5 4 3 2 IE 0 1 RWM 0 0 PGM 0
0
0
0
0
0
6.7 READOUT PROTECTION OPTION The Data EEPROM can be optionally readout protected in ST72334 ROM devices (see option list on
page 145). ST72C334 Flash devices do not have
this protection option.
22/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
7 CENTRAL PROCESSING UNIT
7.1 INTRODUCTION This CPU has a full 8-bit architecture and contains six internal registers allowing efficient 8-bit data manipulation. 7.2 MAIN FEATURES

63 basic instructions Fast 8-bit by 8-bit multiply 17 main addressing modes Two 8-bit index registers 16-bit stack pointer Low power modes Maskable hardware interrupts Non-maskable software interrupt
7.3 CPU REGISTERS The six CPU registers shown in Figure 9 are not present in the memory mapping and are accessed by specific instructions. Figure 9. CPU Registers
7 RESET VALUE = XXh 7 RESET VALUE = XXh 7 RESET VALUE = XXh 15 PCH 87 PCL 0 0 0 0
Accumulator (A) The Accumulator is an 8-bit general purpose register used to hold operands and the results of the arithmetic and logic calculations and to manipulate data. Index Registers (X and Y) In indexed addressing modes, these 8-bit registers are used to create either effective addresses or temporary storage areas for data manipulation. (The Cross-Assembler generates a precede instruction (PRE) to indicate that the following instruction refers to the Y register.) The Y register is not affected by the interrupt automatic procedures (not pushed to and popped from the stack). Program Counter (PC) The program counter is a 16-bit register containing the address of the next instruction to be executed by the CPU. It is made of two 8-bit registers PCL (Program Counter Low which is the LSB) and PCH (Program Counter High which is the MSB).
ACCUMULATOR
X INDEX REGISTER
Y INDEX REGISTER
PROGRAM COUNTER RESET VALUE = RESET VECTOR @ FFFEh-FFFFh 7 111HI 0 NZC CONDITION CODE REGISTER
RESET VALUE = 1 1 1 X 1 X X X 15 87 0 STACK POINTER RESET VALUE = STACK HIGHER ADDRESS X = Undefined Value
23/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CPU REGISTERS (Cont'd) CONDITION CODE REGISTER (CC) Read/Write Reset Value: 111x1xxx
7 1 1 1 H I N Z 0 C
The 8-bit Condition Code register contains the interrupt mask and four flags representative of the result of the instruction just executed. This register can also be handled by the PUSH and POP instructions. These bits can be individually tested and/or controlled by specific instructions. Bit 4 = H Half carry This bit is set by hardware when a carry occurs between bits 3 and 4 of the ALU during an ADD or ADC instruction. It is reset by hardware during the same instructions. 0: No half carry has occurred. 1: A half carry has occurred. This bit is tested using the JRH or JRNH instruction. The H bit is useful in BCD arithmetic subroutines. Bit 3 = I Interrupt mask This bit is set by hardware when entering in interrupt or by software to disable all interrupts except the TRAP software interrupt. This bit is cleared by software. 0: Interrupts are enabled. 1: Interrupts are disabled. This bit is controlled by the RIM, SIM and IRET instructions and is tested by the JRM and JRNM instructions. Note: Interrupts requested while I is set are latched and can be processed when I is cleared. By default an interrupt routine is not interruptible because the I bit is set by hardware at the start of the routine and reset by the IRET instruction at the end of the routine. If the I bit is cleared by software in the interrupt routine, pending interrupts are serviced regardless of the priority level of the current interrupt routine.
Bit 2 = N Negative This bit is set and cleared by hardware. It is representative of the result sign of the last arithmetic, logical or data manipulation. It is a copy of the 7th bit of the result. 0: The result of the last operation is positive or null. 1: The result of the last operation is negative (that is, the most significant bit is a logic 1). This bit is accessed by the JRMI and JRPL instructions. Bit 1 = Z Zero This bit is set and cleared by hardware. This bit indicates that the result of the last arithmetic, logical or data manipulation is zero. 0: The result of the last operation is different from zero. 1: The result of the last operation is zero. This bit is accessed by the JREQ and JRNE test instructions. Bit 0 = C Carry/borrow This bit is set and cleared by hardware and software. It indicates an overflow or an underflow has occurred during the last arithmetic operation. 0: No overflow or underflow has occurred. 1: An overflow or underflow has occurred. This bit is driven by the SCF and RCF instructions and tested by the JRC and JRNC instructions. It is also affected by the "bit test and branch", shift and rotate instructions.
24/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CENTRAL PROCESSING UNIT (Cont'd) Stack Pointer (SP) Read/Write Reset Value: 01 FFh
15 0 7 SP7 SP6 SP5 SP4 SP3 SP2 SP1 0 0 0 0 0 0 8 1 0 SP0
The Stack Pointer is a 16-bit register which is always pointing to the next free location in the stack. It is then decremented after data has been pushed onto the stack and incremented before data is popped from the stack (see Figure 10). Since the stack is 256 bytes deep, the 8th most significant bits are forced by hardware. Following an MCU Reset, or after a Reset Stack Pointer instruction (RSP), the Stack Pointer contains its reset value (the SP7 to SP0 bits are set) which is the stack higher address. Figure 10. Stack Manipulation Example
CALL Subroutine @ 0100h Interrupt Event PUSH Y
The least significant byte of the Stack Pointer (called S) can be directly accessed by a LD instruction. Note: When the lower limit is exceeded, the Stack Pointer wraps around to the stack upper limit, without indicating the stack overflow. The previously stored information is then overwritten and therefore lost. The stack also wraps in case of an underflow. The stack is used to save the return address during a subroutine call and the CPU context during an interrupt. The user may also directly manipulate the stack by means of the PUSH and POP instructions. In the case of an interrupt, the PCL is stored at the first location pointed to by the SP. Then the other registers are stored in the next locations as shown in Figure 10. - When an interrupt is received, the SP is decremented and the context is pushed on the stack. - On return from interrupt, the SP is incremented and the context is popped from the stack. A subroutine call occupies two locations and an interrupt five locations in the stack area.
POP Y
IRET
RET or RSP
SP SP CC A X PCH SP PCH @ 01FFh PCL PCL PCH PCL Y CC A X PCH PCL PCH PCL SP CC A X PCH PCL PCH PCL SP PCH PCL SP
Stack Higher Address = 01FFh Stack Lower Address = 0100h
25/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8 SUPPLY, RESET AND CLOCK MANAGEMENT
The ST72334J/N-Auto, ST72314J/N-Auto and ST72124J-Auto microcontrollers include a range of utility features for securing the application in critical situations (for example, in case of a power brown-out), and reducing the number of external components. An overview is shown in Figure 11. See Section 15 "ELECTRICAL CHARACTERISTICS" on page 108 for more details. Main Features Supply Manager with main supply low voltage detection (LVD) Reset Sequence Manager (RSM) Figure 11. Clock, Reset and Supply Block Diagram
Multi-Oscillator (MO) - 4 Crystal/Ceramic resonator oscillators - 1 External RC oscillator - 1 Internal RC oscillator Clock Security System (CSS) - Clock Filter - Backup Safe Oscillator
CLOCK SECURITY SYSTEM (CSS) OSC2 OSC1 MULTIOSCILLATOR (MO) CLOCK FILTER SAFE OSC fOSC TO MAIN CLOCK CONTROLLER
RESET SEQUENCE RESET MANAGER (RSM) FROM WATCHDOG PERIPHERAL
VDD VSS
LOW VOLTAGE DETECTOR (LVD) CRSR 0 0 0
LVD RF 0
CSS IE D
WDG RF
CSS INTERRUPT
26/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8.1 LOW VOLTAGE DETECTOR (LVD) To allow the integration of power management features in the application, the Low Voltage Detector function (LVD) generates a static reset when the VDD supply voltage is below a VIT- reference value. This means that it secures the power-up as well as the power-down keeping the ST7 in reset. The VIT- reference value for a voltage drop is lower than the VIT+ reference value for power-on in order to avoid a parasitic reset when the MCU starts running and sinks current on the supply (hysteresis). The LVD Reset circuitry generates a reset when VDD is below: - VIT+ when VDD is rising - VIT- when VDD is falling The LVD function is illustrated in the Figure 12. Provided the minimum VDD value (guaranteed for the oscillator frequency) is above VIT-, the MCU can only be in two modes: - under full software control - in static safe reset Figure 12. Low Voltage Detector vs Reset VDD In these conditions, secure operation is always ensured for the application without the need for external reset hardware. During a Low Voltage Detector Reset, the RESET pin is held low, thus permitting the MCU to reset other devices. Notes: 1. The LVD allows the device to be used without any external RESET circuitry. 2. Three different reference levels are selectable through the option byte according to the application requirement. LVD application note Application software can detect a reset caused by the LVD by reading the LVDRF bit in the CRSR register. This bit is set by hardware when a LVD reset is generated and cleared by software (writing zero).
Vhyst VIT+ VIT-
RESET
27/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8.2 RESET SEQUENCE MANAGER (RSM) 8.2.1 Introduction The reset sequence manager includes three RESET sources as shown in Figure 14: External RESET source pulse Internal LVD RESET (Low Voltage Detection) Internal WATCHDOG RESET These sources act on the RESET pin and it is always kept low during the delay phase. The RESET service routine vector is fixed at addresses FFFEh-FFFFh in the ST7 memory map. The basic RESET sequence consists of three phases as shown in Figure 13: Delay depending on the RESET source 4096 CPU clock cycle delay RESET vector fetch Figure 14. Reset Block Diagram The 4096 CPU clock cycle delay allows the oscillator to stabilise and ensures that recovery has taken place from the Reset state. The RESET vector fetch phase duration is 2 clock cycles. Figure 13. RESET Sequence Phases
RESET DELAY INTERNAL RESET 4096 CLOCK CYCLES FETCH VECTOR
VDD
fCPU COUNTER
INTERNAL RESET
RON
RESET
WATCHDOG RESET LVD RESET
28/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
RESET SEQUENCE MANAGER (Cont'd) 8.2.2 Asynchronous External RESET Pin The RESET pin is both an input and an open-drain output with integrated RON weak pull-up resistor. This pull-up has no fixed value but varies in accordance with the input voltage. It can be pulled low by external circuitry to reset the device. See ELECTRICAL CHARACTERISTICS section for more details. A RESET signal originating from an external source must have a duration of at least th(RSTL)in in order to be recognized. This detection is asynchronous and therefore the MCU can enter reset state even in Halt mode. The RESET pin is an asynchronous signal which plays a major role in EMS performance. In a noisy environment, it is recommended to follow the guidelines mentioned in the ELECTRICAL CHARACTERISTICS section. Two RESET sequences can be associated with this RESET source: short or long external reset pulse (see Figure 15). Starting from the external RESET pulse recognition, the device RESET pin acts as an output that is pulled low during at least tw(RSTL)out. Figure 15. RESET Sequences VDD
VIT+ VIT-
8.2.3 Internal Low Voltage Detection RESET Two different RESET sequences caused by the internal LVD circuitry can be distinguished: Power-On RESET Voltage Drop RESET The device RESET pin acts as an output that is pulled low when VDDLVD RESET
SHORT EXT. RESET
LONG EXT. RESET
WATCHDOG RESET
RUN
DELAY
RUN
DELAY
RUN
DELAY
RUN
DELAY
RUN
tw(RSTL)out th(RSTL)in
EXTERNAL RESET SOURCE
th(RSTL)in
tw(RSTL)out
RESET PIN
WATCHDOG RESET WATCHDOG UNDERFLOW INTERNAL RESET (4096 TCPU) FETCH VECTOR
29/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8.3 MULTI-OSCILLATOR (MO) The main clock of the ST7 can be generated by four different source types coming from the multioscillator block: an external source 4 crystal or ceramic resonator oscillators an external RC oscillator an internal high frequency RC oscillator Each oscillator is optimized for a given frequency range in terms of consumption and is selectable through the option byte. The associated hardware configuration are shown in Table 4. Refer to the ELECTRICAL CHARACTERISTICS section for more details. External Clock Source In this external clock mode, a clock signal (square, sinus or triangle) with ~50% duty cycle has to drive the OSC1 pin while the OSC2 pin is tied to ground. Crystal/Ceramic Oscillators This family of oscillators has the advantage of producing a very accurate rate on the main clock of the ST7. The selection within a list of four oscillators with different frequency ranges has to be done by option byte in order to reduce consumption. In this mode of the multi-oscillator, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion and start-up stabilization time. The loading capacitance values must be adjusted according to the selected oscillator. These oscillators are not stopped during the RESET phase to avoid losing time in the oscillator start-up phase. External RC Oscillator This oscillator allows a low cost solution for the main clock of the ST7 using only an external resistor and an external capacitor. The frequency of the external RC oscillator (in the range of some MHz) is fixed by the resistor and the capacitor values. Consequently in this MO mode, the accuracy of the clock is dependent on VDD, TA, process variations and the accuracy of the discrete components used. This option should not be used in applications that require accurate timing. Internal RC Oscillator The internal RC oscillator mode is based on the same principle as the external RC oscillator including the resistance and the capacitance of the device. This mode is the most cost effective one with the drawback of a lower frequency accuracy. Its frequency is in the range of several MHz. This option should not be used in applications that require accurate timing. In this mode, the two oscillator pins have to be tied to ground. Table 4. ST7 Clock Sources
Hardware Configuration
External Clock
ST7 OSC1 OSC2
EXTERNAL SOURCE
Crystal/Ceramic Resonators
ST7 OSC1 OSC2
CL1
LOAD CAPACITORS
ST7 OSC1 OSC2
CL2
External RC Oscillator
REX
CEX
Internal RC Oscillator
ST7 OSC1 OSC2
30/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
31/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8.4 CLOCK SECURITY SYSTEM (CSS) The Clock Security System (CSS) protects the ST7 against main clock problems. To allow the integration of the security features in the applications, it is based on a clock filter control and an internal safe oscillator. The CSS can be enabled or disabled by option byte. 8.4.1 Clock Filter Control The clock filter is based on a clock frequency limitation function. This filter function is able to detect and filter high frequency spikes on the ST7 main clock. If the oscillator is not working properly (e.g. working at a harmonic frequency of the resonator), the current active oscillator clock can be totally filtered, and then no clock signal is available for the ST7 from this oscillator anymore. If the original clock source recovers, the filtering is stopped automatically and the oscillator supplies the ST7 clock. 8.4.2 Safe Oscillator Control The safe oscillator of the CSS block is a low frequency back-up clock source (see Figure 16). If the clock signal disappears (due to a broken or disconnected resonator...) during a safe oscillator period, the safe oscillator delivers a low frequency clock signal which allows the ST7 to perform some rescue operations. Automatically, the ST7 clock source switches back from the safe oscillator if the original clock source recovers. Limitation detection The automatic safe oscillator selection is notified by hardware setting the CSSD bit of the CRSR register. An interrupt can be generated if the CSSIE bit has been previously set. These 2 bits are described in the CRSR register description. 8.4.3 Low Power Modes
Mode WAIT Description No effect on CSS. CSS interrupt cause the device to exit from Wait mode. The CRSR register is frozen. The CSS (including the safe oscillator) is disabled until Halt mode is exited. The previous CSS configuration resumes when the MCU is woken up by an interrupt with "exit from Halt mode" capability or from the counter reset value when the MCU is woken up by a RESET.
HALT
8.4.4 Interrupts The CSS interrupt event generates an interrupt if the corresponding Enable Control Bit (CSSIE) is set and the interrupt mask in the CC register is reset (RIM instruction).
Interrupt Event Enable Event Control Flag Bit CSSIE Exit from Wait Yes Exit from Halt1) No
CSS event detection (safe oscillator acti- CSSD vated as main clock)
Notes: 1. This interrupt allows to exit from Active Halt mode if this mode is available in the MCU.
Figure 16. Clock Filter Function and Safe Oscillator Function
CLOCK FILTER FUNCTION
fOSC/2 fCPU
SAFE OSCILLATOR FUNCTION
fOSC/2 fSFOSC fCPU
32/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8.5 SUPPLY, RESET AND CLOCK REGISTER DESCRIPTION Read / Write Reset Value: 000x 000x (xxh)
7 0 0 0 LVD RF 0 CSS IE 0 CSS WDG D RF
Bit 7:5 = Reserved, always read as 0. Bit 4 = LVDRF LVD reset flag This bit indicates that the last RESET was generated by the LVD block. It is set by hardware (LVD reset) and cleared by software (writing zero). See WDGRF flag description for more details. When the LVD is disabled by option byte, the LVDRF bit value is undefined. Bit 3 = Reserved, always read as 0. Bit 2 = CSSIE Clock security syst. interrupt enable This bit enables the interrupt when a disturbance is detected by the clock security system (CSSD bit set). It is set and cleared by software. 0: Clock security system interrupt disabled 1: Clock security system interrupt enabled Refer to Table 6, "Interrupt Mapping," on page 35 for more details on the CSS interrupt vector. When the CSS is disabled by option byte, the CSSIE bit has no effect.
Bit 1 = CSSD Clock security system detection This bit indicates that the safe oscillator of the clock security system block has been selected by hardware due to a disturbance on the main clock signal (fOSC). It is set by hardware and cleared by reading the CRSR register when the original oscillator recovers. 0: Safe oscillator is not active 1: Safe oscillator has been activated When the CSS is disabled by option byte, the CSSD bit value is forced to 0. Bit 0 = WDGRF Watchdog reset flag This bit indicates that the last RESET was generated by the watchdog peripheral. It is set by hardware (Watchdog RESET) and cleared by software (writing zero) or an LVD RESET (to ensure a stable cleared state of the WDGRF flag when the CPU starts). Combined with the LVDRF flag information, the flag description is given by the following table.
RESET Sources External RESET pin Watchdog LVD LVDRF 0 0 1 WDGRF 0 1 X
Application notes The LVDRF flag is not cleared when another RESET type occurs (external or watchdog), the LVDRF flag remains set to keep trace of the original failure. In this case, a watchdog reset can be detected by software while an external reset can not.
Table 5. Clock, Reset and Supply Register Map and Reset Values
Address (Hex.) 002Bh Register Label CRSR Reset Value 7 6 5 4 LVDRF x 3 2 CFIE 0 1 CSSD 0 0 WDGRF x
0
0
0
0
33/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
9 INTERRUPTS
The ST7 core may be interrupted by one of two different methods: maskable hardware interrupts as listed in the Interrupt Mapping table and a nonmaskable software interrupt (TRAP). The Interrupt processing flowchart is shown in Figure 17. The maskable interrupts must be enabled by clearing the I bit in order to be serviced. However, disabled interrupts may be latched and processed when they are enabled (see EXTERNAL INTERRUPTS subsection). Note: After reset, all interrupts are disabled. When an interrupt has to be serviced: - Normal processing is suspended at the end of the current instruction execution. - The PC, X, A and CC registers are saved onto the stack. - The I bit of the CC register is set to prevent additional interrupts. - The PC is then loaded with the interrupt vector of the interrupt to service and the first instruction of the interrupt service routine is fetched (refer to the Interrupt Mapping table for vector addresses). The interrupt service routine should finish with the IRET instruction which causes the contents of the saved registers to be recovered from the stack. Note: As a consequence of the IRET instruction, the I bit will be cleared and the main program will resume. Priority Management By default, a servicing interrupt cannot be interrupted because the I bit is set by hardware entering in interrupt routine. In the case when several interrupts are simultaneously pending, a hardware priority defines which one will be serviced first (see the Interrupt Mapping table). Interrupts and Low Power Mode All interrupts allow the processor to leave the Wait low power mode. Only external and specifically mentioned interrupts allow the processor to leave the Halt low power mode (refer to the "Exit from Halt" column in the Interrupt Mapping table). 9.1 NON-MASKABLE SOFTWARE INTERRUPT This interrupt is entered when the TRAP instruction is executed regardless of the state of the I bit. It will be serviced according to the flowchart on Figure 17. 9.2 EXTERNAL INTERRUPTS External interrupt vectors can be loaded into the PC register if the corresponding external interrupt occurred and if the I bit is cleared. These interrupts allow the processor to leave the Halt low power mode. The external interrupt polarity is selected through the miscellaneous register or interrupt register (if available). An external interrupt triggered on edge will be latched and the interrupt request automatically cleared upon entering the interrupt service routine. If several input pins, connected to the same interrupt vector, are configured as interrupts, their signals are logically NANDed before entering the edge/level detection block. Caution: The type of sensitivity defined in the Miscellaneous or Interrupt register (if available) applies to the ei source. In case of a NANDed source (as described in the I/O PORTS section), a low level on an I/O pin configured as input with interrupt, masks the interrupt request even in case of rising-edge sensitivity. 9.3 PERIPHERAL INTERRUPTS Different peripheral interrupt flags in the status register are able to cause an interrupt when they are active if both: - The I bit of the CC register is cleared. - The corresponding enable bit is set in the control register. If any of these two conditions is false, the interrupt is latched and thus remains pending. Clearing an interrupt request is done by: - Writing "0" to the corresponding bit in the status register or - Access to the status register while the flag is set followed by a read or write of an associated register. Note: The clearing sequence resets the internal latch. A pending interrupt (that is, waiting to be enabled) will therefore be lost if the clear sequence is executed.
34/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
INTERRUPTS (Cont'd) Figure 17. Interrupt Processing Flowchart
FROM RESET I BIT SET? Y N N
INTERRUPT PENDING? Y
FETCH NEXT INSTRUCTION
N
IRET? Y
STACK PC, X, A, CC SET I BIT LOAD PC FROM INTERRUPT VECTOR
EXECUTE INSTRUCTION
RESTORE PC, X, A, CC FROM STACK THIS CLEARS I BIT BY DEFAULT
Table 6. Interrupt Mapping
No. Source Block RESET TRAP 0 1 2 3 4 5 6 7 8 9 10 11 12 13 SPI TIMER A TIMER B SCI MCC/RTC CSS ei0 ei1 ei2 ei3 Reset Software Interrupt Not used Main Clock Controller Time Base Interrupt or Clock Security System Interrupt External Interrupt Port A3..0 External Interrupt Port F2..0 External Interrupt Port B3..0 External Interrupt Port B7..4 Not used SPI Peripheral Interrupts TIMER A Peripheral Interrupts TIMER B Peripheral Interrupts SCI Peripheral Interrupts SPISR TASR TBSR SCISR EECSR Lowest Priority no N/A MCCSR CRSR yes Description Register Label N/A Priority Order Highest Priority Exit from Halt1) yes no Address Vector FFFEh-FFFFh FFFCh-FFFDh FFFAh-FFFBh FFF8h-FFF9h FFF6h-FFF7h FFF4h-FFF5h FFF2h-FFF3h FFF0h-FFF1h FFEEh-FFEFh FFECh-FFEDh FFEAh-FFEBh FFE8h-FFE9h FFE6h-FFE7h FFE4h-FFE5h FFE2h-FFE3h FFE0h-FFE1h
Data-EEPROM Data EEPROM Interrupt Not used
Notes: 1. Valid for Halt and Active Halt modes except for the MCC/RTC or CSS interrupt source which exits from Active Halt mode only.
35/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
10 POWER SAVING MODES
10.1 INTRODUCTION To give a large measure of flexibility to the application in terms of power consumption, four main power saving modes are implemented in the ST7 (see Figure 18): Slow, Wait (Slow Wait), Active Halt and Halt. After a RESET the normal operating mode is selected by default (RUN mode). This mode drives the device (CPU and embedded peripherals) by means of a master clock which is based on the main oscillator frequency divided by 2 (fCPU). From RUN mode, the different power saving modes may be selected by setting the relevant register bits or by calling the specific ST7 software instruction whose action depends on the oscillator status. Figure 18. Power Saving Mode Transitions
High RUN SLOW
MISCR1
10.2 SLOW MODE This mode has two targets: - To reduce power consumption by decreasing the internal clock in the device, - To adapt the internal clock frequency (fCPU) to the available supply voltage. Slow mode is controlled by three bits in the MISCR1 register: the SMS bit which enables or disables Slow mode and two CPx bits which select the internal slow frequency (fCPU). In this mode, the oscillator frequency can be divided by 4, 8, 16 or 32 instead of 2 in normal operating mode. The CPU and peripherals are clocked at this lower frequency. Note: Slow Wait mode is activated when entering the Wait mode while the device is already in Slow mode. Figure 19. Slow Mode Clock Transitions
fOSC/4 fCPU fOSC/8 fOSC/2
fOSC/2 CP1:0 SMS 00 01
WAIT SLOW WAIT ACTIVE HALT HALT Low POWER CONSUMPTION
NEW SLOW FREQUENCY REQUEST
NORMAL RUN MODE REQUEST
36/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
POWER SAVING MODES (Cont'd) 10.3 WAIT MODE Wait mode places the MCU in a low power consumption mode by stopping the CPU. This power saving mode is selected by calling the WFI instruction. All peripherals remain active. During Wait mode, the I bit of the CC register is cleared, to enable all interrupts. All other registers and memory remain unchanged. The MCU remains in Wait mode until an interrupt or RESET occurs, whereupon the Program Counter branches to the starting address of the interrupt or Reset service routine. The MCU will remain in Wait mode until a Reset or an Interrupt occurs, causing it to wake up. Refer to Figure 20. Figure 20. Wait Mode Flowchart
OSCILLATOR PERIPHERALS CPU I BIT ON ON OFF 0
WFI INSTRUCTION
N RESET N INTERRUPT Y OSCILLATOR PERIPHERALS CPU I BIT ON OFF ON 0 Y
4096 CPU CLOCK CYCLE DELAY
OSCILLATOR PERIPHERALS CPU I BIT
ON ON ON X 1)
FETCH RESET VECTOR OR SERVICE INTERRUPT
Note: 1. Before servicing an interrupt, the CC register is pushed on the stack. The I bit of the CC register is set during the interrupt routine and cleared when the CC register is popped.
37/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
POWER SAVING MODES (Cont'd) 10.4 ACTIVE HALT AND HALT MODES Active Halt and Halt modes are the two lowest power consumption modes of the MCU. They are both entered by executing the HALT instruction. The decision to enter either in Active Halt or Halt mode is given by the MCC/RTC interrupt enable flag (OIE bit in MCCSR register).
MCCSR OIE bit 0 1 Power Saving Mode entered when HALT instruction is executed Halt mode Active Halt mode HALT INSTRUCTION (MCCSR.OIE=1) OSCILLATOR ON PERIPHERALS 1) OFF CPU OFF I BIT 0
Figure 21. Active Halt Timing Overview
RUN ACTIVE HALT 4096 CPU CYCLE DELAY RESET OR INTERRUPT RUN
HALT INSTRUCTION [MCCSR.OIE=1]
FETCH VECTOR
Figure 22. Active Halt Mode Flowchart
10.4.1 Active Halt Mode Active Halt mode is the lowest power consumption mode of the MCU with a real-time clock available. It is entered by executing the HALT instruction when the OIE bit of the Main Clock Controller Status register (MCCSR) is set (see Section 13.2 "MAIN CLOCK CONTROLLER WITH REAL-TIME CLOCK TIMER (MCC/RTC)" on page 53 for more details on the MCCSR register). The MCU can exit Active Halt mode on reception of either an MCC/RTC interrupt, a specific interrupt (see Table 6, "Interrupt Mapping," on page 35) or a RESET. When exiting Active Halt mode by means of a RESET or an interrupt, a 4096 CPU cycle delay occurs. After the start up delay, the CPU resumes operation by servicing the interrupt or by fetching the reset vector which woke it up (see Figure 22). When entering Active Halt mode, the I bit in the CC register is cleared to enable interrupts. Therefore, if an interrupt is pending, the MCU wakes up immediately. In Active Halt mode, only the main oscillator and its associated counter (MCC/RTC) are running to keep a wake-up time base. All other peripherals are not clocked except those which get their clock supply from another clock generator (such as external or auxiliary oscillator). The safeguard against staying locked in Active Halt mode is provided by the oscillator interrupt. Note: As soon as the interrupt capability of one of the oscillators is selected (MCCSR.OIE bit set), entering Active Halt mode while the Watchdog is active does not generate a RESET. This means that the device cannot spend more than a defined delay in this power saving mode.
N RESET N Y INTERRUPT 2) Y OSCILLATOR ON PERIPHERALS 1) OFF CPU ON I BIT X 3) 4096 CPU CLOCK CYCLE DELAY OSCILLATOR PERIPHERALS CPU I BITS ON ON ON X 3)
FETCH RESET VECTOR OR SERVICE INTERRUPT
Notes: 1. Peripheral clocked with an external clock source can still be active. 2. Only the MCC/RTC interrupt and some specific interrupts can exit the MCU from Active Halt mode (such as external interrupt). Refer to Table 6, "Interrupt Mapping," on page 35 for more details. 3. Before servicing an interrupt, the CC register is pushed on the stack. The I bit of the CC register is set during the interrupt routine and cleared when the CC register is popped.
38/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
POWER SAVING MODES (Cont'd) 10.4.2 Halt Mode The Halt mode is the lowest power consumption mode of the MCU. It is entered by executing the HALT instruction when the OIE bit of the Main Clock Controller Status register (MCCSR) is cleared (see Section 13.2 "MAIN CLOCK CONTROLLER WITH REAL-TIME CLOCK TIMER (MCC/RTC)" on page 53 for more details on the MCCSR register). The MCU can exit Halt mode on reception of either a specific interrupt (see Table 6, "Interrupt Mapping," on page 35) or a RESET. When exiting Halt mode by means of a RESET or an interrupt, the oscillator is immediately turned on and the 4096 CPU cycle delay is used to stabilize the oscillator. After the start up delay, the CPU resumes operation by servicing the interrupt or by fetching the reset vector which woke it up (see Figure 24). When entering Halt mode, the I bit in the CC register is forced to 0 to enable interrupts. Therefore, if an interrupt is pending, the MCU wakes immediately. In Halt mode, the main oscillator is turned off causing all internal processing to be stopped, including the operation of the on-chip peripherals. All peripherals are not clocked except the ones which get their clock supply from another clock generator (such as an external or auxiliary oscillator). The compatibility of Watchdog operation with Halt mode is configured by the "WDGHALT" option bit of the option byte. The HALT instruction when executed while the Watchdog system is enabled, can generate a Watchdog RESET (see Section 17.2 on page 143 for more details). Figure 23. HALT Timing Overview
RUN HALT 4096 CPU CYCLE DELAY RESET OR INTERRUPT FETCH VECTOR RUN FETCH RESET VECTOR OR SERVICE INTERRUPT
Figure 24. Halt Mode Flowchart
HALT INSTRUCTION (MCCSR.OIE=0) ENABLE WDGHALT 1) 1 WATCHDOG RESET OSCILLATOR OFF PERIPHERALS 2) OFF CPU OFF I BIT 0 0 WATCHDOG DISABLE
N RESET N Y INTERRUPT 3) Y OSCILLATOR PERIPHERALS CPU I BIT ON OFF ON X 4)
4096 CPU CLOCK CYCLE DELAY OSCILLATOR PERIPHERALS CPU I BITS ON ON ON X 4)
HALT INSTRUCTION [MCCSR.OIE=0]
Notes: 1. WDGHALT is an option bit. See OPTION BYTES section for more details. 2. Peripheral clocked with an external clock source can still be active. 3. Only some specific interrupts can exit the MCU from Halt mode (such as external interrupt). Refer to Table 6, "Interrupt Mapping," on page 35 for more details. 4. Before servicing an interrupt, the CC register is pushed on the stack. The I bit of the CC register is set during the interrupt routine and cleared when the CC register is popped.
39/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
11 I/O PORTS
11.1 INTRODUCTION The I/O ports offer different functional modes: - transfer of data through digital inputs and outputs and for specific pins: - external interrupt generation - alternate signal input/output for the on-chip peripherals. An I/O port contains up to eight pins. Each pin can be programmed independently as digital input (with or without interrupt generation) or digital output. 11.2 FUNCTIONAL DESCRIPTION Each port has two main registers: - Data Register (DR) - Data Direction Register (DDR) and one optional register: - Option Register (OR) Each I/O pin may be programmed using the corresponding register bits in the DDR and OR registers: bit X corresponding to pin X of the port. The same correspondence is used for the DR register. The following description takes into account the OR register (for specific ports which do not provide this register refer to the I/O PORT IMPLEMENTATION section). The generic I/O block diagram is shown in Figure 25. 11.2.1 Input Modes The input configuration is selected by clearing the corresponding DDR register bit. In this case, reading the DR register returns the digital value applied to the external I/O pin. Different input modes can be selected by software through the OR register. Notes: 1. Writing the DR register modifies the latch value but does not affect the pin status. 2. When switching from input to output mode, the DR register has to be written first to drive the correct level on the pin as soon as the port is configured as an output. 3. Do not use read/modify/write instructions (BSET or BRES) to modify the DR register. External interrupt function When an I/O is configured as Input with Interrupt, an event on this I/O can generate an external interrupt request to the CPU. Each pin can independently generate an interrupt request. The interrupt sensitivity is independently programmable using the sensitivity bits in the Miscellaneous register. Each external interrupt vector is linked to a dedicated group of I/O port pins (see pinout description and interrupt section). If several input pins are selected simultaneously as interrupt source, these are logically NANDed. For this reason if one of the interrupt pins is tied low, it masks the other ones. In case of a floating input with interrupt configuration, special care must be taken when changing the configuration (see Figure 26). The external interrupts are hardware interrupts, which means that the request latch (not accessible directly by the application) is automatically cleared when the corresponding interrupt vector is fetched. To clear an unwanted pending interrupt by software, the sensitivity bits in the Miscellaneous register must be modified. 11.2.2 Output Modes The output configuration is selected by setting the corresponding DDR register bit. In this case, writing the DR register applies this digital value to the I/O pin through the latch. Then reading the DR register returns the previously stored value. Two different output modes can be selected by software through the OR register: Output push-pull and open-drain. DR register value and output pin status:
DR 0 1 Push-pull VSS VDD Open-drain VSS Floating
11.2.3 Alternate Functions When an on-chip peripheral is configured to use a pin, the alternate function is automatically selected. This alternate function takes priority over the standard I/O programming. When the signal is coming from an on-chip peripheral, the I/O pin is automatically configured in output mode (push-pull or open drain according to the peripheral). When the signal is going to an on-chip peripheral, the I/O pin must be configured in input mode. In this case, the pin state is also digitally readable by addressing the DR register. Note: Input pull-up configuration can cause unexpected value at the input of the alternate peripheral input. When an on-chip peripheral use a pin as input and output, this pin has to be configured in input floating mode.
40/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORTS (Cont'd) Figure 25. I/O Port General Block Diagram
REGISTER ACCESS ALTERNATE OUTPUT 1 0 ALTERNATE ENABLE DR
VDD
P-BUFFER (see table below) PULL-UP (see table below) VDD
DDR PULL-UP CONFIGURATION If implemented OR SEL N-BUFFER DDR SEL CMOS SCHMITT TRIGGER ANALOG INPUT DIODES (see table below) PAD
OR
EXTERNAL INTERRUPT SOURCE (eix)
Table 7. I/O Port Mode Options
Configuration Mode Input Floating with/without Interrupt Pull-up with/without Interrupt Push-pull Open Drain (logic level) True Open Drain Pull-Up Off On Off NI P-Buffer Off On Off NI On On Diodes to VDD to VSS
Output
Legend: NI - not implemented Off - implemented not activated On - implemented and activated
DATA BUS
DR SEL
1 0
ALTERNATE INPUT FROM OTHER BITS
POLARITY SELECTION
NI (see note)
Note: The diode to VDD is not implemented in the true open drain pads. A local protection between the pad and VSS is implemented to protect the device against positive stress.
41/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORTS (Cont'd) Table 8. I/O Port Configurations
Hardware Configuration
NOT IMPLEMENTED IN TRUE OPEN DRAIN I/O PORTS VDD RPU PAD PULL-UP CONFIGURATION DR REGISTER ACCESS
DR REGISTER
W DATA BUS R
INPUT 1)
ALTERNATE INPUT FROM OTHER PINS INTERRUPT CONFIGURATION POLARITY SELECTION ANALOG INPUT NOT IMPLEMENTED IN TRUE OPEN DRAIN I/O PORTS EXTERNAL INTERRUPT SOURCE (eix)
OPEN-DRAIN OUTPUT 2)
VDD RPU
DR REGISTER ACCESS
PAD
DR REGISTER
R/W
DATA BUS
ALTERNATE ENABLE
ALTERNATE OUTPUT
PUSH-PULL OUTPUT 2)
NOT IMPLEMENTED IN TRUE OPEN DRAIN I/O PORTS
VDD RPU
DR REGISTER ACCESS
PAD
DR REGISTER
R/W
DATA BUS
ALTERNATE ENABLE
ALTERNATE OUTPUT
Notes: 1. When the I/O port is in input configuration and the associated alternate function is enabled as an output, reading the DR register will read the alternate function output status. 2. When the I/O port is in output configuration and the associated alternate function is enabled as an input, the alternate function reads the pin status given by the DR register content.
42/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORTS (Cont'd) CAUTION: The alternate function must not be activated as long as the pin is configured as input with interrupt, in order to avoid generating spurious interrupts. Analog alternate function When the pin is used as an ADC input, the I/O must be configured as floating input. The analog multiplexer (controlled by the ADC registers) switches the analog voltage present on the selected pin to the common analog rail which is connected to the ADC input. It is recommended not to change the voltage level or loading on any port pin while conversion is in progress. Furthermore it is recommended not to have clocking pins located close to a selected analog pin. WARNING: The analog input voltage level must be within the limits stated in the absolute maximum ratings. 11.3 I/O PORT IMPLEMENTATION The hardware implementation on each I/O port depends on the settings in the DDR and OR registers and specific feature of the I/O port such as ADC Input or true open drain. Switching these I/O ports from one state to another should be done in a sequence that prevents unwanted side effects. Recommended safe transitions are illustrated in Figure 26. Other transitions are potentially risky and should be avoided, since they are likely to present unwanted side-effects such as spurious interrupt generation. Figure 26. Interrupt I/O Port State Transitions
01 00 10 OUTPUT open-drain 11 OUTPUT push-pull
Standard Ports PA5:4, PC7:0, PD7:0, PE7:4, PE1:0, PF7:6, PF4
MODE floating input pull-up input open drain output push-pull output DDR 0 0 1 1 OR 0 1 0 1
Interrupt Ports PA2:0, PB7:5, PB2:0, PF1:0 (with pull-up)
MODE floating input pull-up interrupt input open drain output push-pull output DDR 0 0 1 1 OR 0 1 0 1
PA3, PB4, PB3, PF2 (without pull-up)
MODE floating input floating interrupt input open drain output push-pull output DDR 0 0 1 1 OR 0 1 0 1
True Open Drain Ports PA7:6
MODE floating input open drain (high sink ports) DDR 0 1
INPUT INPUT floating/pull-up floating interrupt (reset state)
XX = DDR, OR
The I/O port register configurations are summarized as follows.
43/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORTS (Cont'd) 11.4 LOW POWER MODES
Mode WAIT HALT Description No effect on I/O ports. External interrupts cause the device to exit from Wait mode. No effect on I/O ports. External interrupts cause the device to exit from Halt mode.
11.5 INTERRUPTS The external interrupt event generates an interrupt if the corresponding configuration is selected with DDR and OR registers and the I-bit in the CC register is reset (RIM instruction).
Interrupt Event External interrupt on selected external event Enable Event Control Flag Bit DDRx ORx Exit from Wait Yes Exit from Halt Yes
Table 9. Port Configuration
Port Pin name PA7:6 PA5:4 PA3 PA2:0 PB4:3 PB7:5, PB2:0 PC7:4, PC1:0 PC3:2 PD7:0 PE7:4 PE1:0 PF7:6 PF4 PF2 PF1:0 Input OR = 0 floating floating floating floating floating floating floating floating floating floating floating floating floating floating floating pull-up floating interrupt pull-up interrupt floating interrupt pull-up interrupt pull-up pull-up pull-up pull-up pull-up pull-up pull-up floating interrupt pull-up interrupt OR = 1 Output OR = 0 OR = 1 true open-drain open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull open drain push-pull High-Sink Yes
Port A
Port B Port C Port D Port E
No
Yes No Yes No Yes No
Port F
44/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORTS (Cont'd) 11.5.1 Register Description DATA REGISTER (DR) Port x Data Register PxDR with x = A, B, C, D, E or F. Read / Write Reset Value: 0000 0000 (00h)
7 D7 D6 D5 D4 D3 D2 D1 0 D0
OPTION REGISTER (OR) Port x Option Register PxOR with x = A, B, C, D, E or F. Read / Write Reset Value: 0000 0000 (00h)
7 O7 O6 O5 O4 O3 O2 O1 0 O0
Bit 7:0 = D[7:0] Data register 8 bits. The DR register has a specific behavior according to the selected input/output configuration. Writing the DR register is always taken into account even if the pin is configured as an input; this allows to always have the expected level on the pin when toggling to output mode. Reading the DR register returns either the DR register latch content (pin configured as output) or the digital value applied to the I/O pin (pin configured as input). DATA DIRECTION REGISTER (DDR) Port x Data Direction Register PxDDR with x = A, B, C, D, E or F. Read / Write Reset Value: 0000 0000 (00h)
7 DD7 DD6 DD5 DD4 DD3 DD2 DD1 0 DD0
Bit 7:0 = O[7:0] Option register 8 bits. For specific I/O pins, this register is not implemented. In this case the DDR register is enough to select the I/O pin configuration. The OR register allows to distinguish: in input mode if the pull-up with interrupt capability or the basic pull-up configuration is selected, in output mode if the push-pull or open drain configuration is selected. Each bit is set and cleared by software. Input mode: 0: floating input 1: pull-up input with or without interrupt Output mode: 0: output open drain (with P-Buffer deactivated) 1: output push-pull
Bit 7:0 = DD[7:0] Data direction register 8 bits. The DDR register gives the input/output direction configuration of the pins. Each bits is set and cleared by software. 0: Input mode 1: Output mode
45/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORTS (Cont'd) Table 10. I/O Port Register Map and Reset Values
Address (Hex.) Register Label 7 0 6 0 5 0 4 0 3 0 2 0 1 0 0 0
Reset Value of all IO port registers 0000h 0001h 0002h 0004h 0005h 0006h 0008h 0009h 000Ah 000Ch 000Dh 000Eh 0010h 0011h 0012h 0014h 0015h 0016h PADR PADDR PAOR 1) PCDR PCDDR PCOR PBDR PBDDR PBOR 1) PEDR PEDDR PEOR 1) PDDR PDDDR PDOR 1) PFDR PFDDR PFOR
MSB
LSB
MSB
LSB
MSB
LSB
MSB
LSB
MSB
LSB
MSB
LSB
Notes: 1) The bits corresponding to unavailable pins are forced to 1 by hardware, this affects the reset status value.
46/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
12 MISCELLANEOUS REGISTERS
The miscellaneous registers allow control over several different features such as the external interrupts or the I/O alternate functions. 12.1 I/O PORT INTERRUPT SENSITIVITY The external interrupt sensitivity is controlled by the ISxx bits of the MISCR1 miscellaneous register. This control allows to have two fully independent external interrupt source sensitivities. Each external interrupt source can be generated on four different events on the pin: Falling edge Rising edge Falling and rising edge Falling edge and low level To guarantee correct functionality, the sensitivity bits in the MISCR1 register must be modified only when the I bit of the CC register is set to 1 (interrupt masked). See I/O port register and Miscellaneous register descriptions for more details on the programming. 12.2 I/O PORT ALTERNATE FUNCTIONS The MISCR registers manage four I/O port miscellaneous alternate functions: Main clock signal (fCPU) output on PF0 A beep signal output on PF1 (with 3 selectable audio frequencies) SPI pin configuration: - SS pin internal control to use the PC7 I/O port function while the SPI is active. These functions are described in detail in the Section 12 "MISCELLANEOUS REGISTERS" on page 47. Figure 27. Ext. Interrupt Sensitivity
MISCR1 IS10 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 MISCR1 IS20 PA0 PA1 PA2 PA3 PF0 PF1 PF2 INTERRUPT SOURCE ei0 ei1 IS21 INTERRUPT SOURCE ei2 ei3 IS11
SENSITIVITY CONTROL
SENSITIVITY CONTROL
47/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
MISCELLANEOUS REGISTERS (Cont'd) 12.3 REGISTERS DESCRIPTION MISCELLANEOUS REGISTER 1 (MISCR1) Read / Write Reset Value: 0000 0000 (00h)
7 IS11 IS10 MCO IS21 IS20 CP1 CP0 0 SMS
Bit 4:3 = IS2[1:0] ei0 and ei1 sensitivity The interrupt sensitivity, defined using the IS2[1:0] bits, is applied to the following external interrupts:ei0 (port A3..0) and ei1 (port F2..0). These 2 bits can be written only when the I bit of the CC register is set to 1 (interrupt disabled). Bit 2:1 = CP[1:0] CPU clock prescaler These bits select the CPU clock prescaler which is applied in the different slow modes. Their action is conditioned by the setting of the SMS bit. These 2 bits are set and cleared by software.
fCPU in Slow mode fOSC / 4 fOSC / 8 fOSC / 16 fOSC / 32 CP1 CP0 0 1 0 1 0 0 1 1
Bit 7:6 = IS1[1:0] ei2 and ei3 sensitivity The interrupt sensitivity, defined using the IS1[1:0] bits, is applied to the following external interrupts: ei2 (port B3..0) and ei3 (port B7..4). These 2 bits can be written only when the I bit of the CC register is set to 1 (interrupt disabled).
External Interrupt Sensitivity Falling edge and low level Rising edge only Falling edge only Rising and falling edge IS11 IS10 0 0 1 1 0 1 0 1
Bit 5 = MCO Main clock out selection This bit enables the MCO alternate function on the I/O port. It is set and cleared by software. 0: MCO alternate function disabled (I/O pin free for general-purpose I/O) 1: MCO alternate function enabled (fOSC/2 on I/O port) Note: To reduce power consumption, the MCO function is not active in Active Halt mode.
Bit 0 = SMS Slow mode select This bit is set and cleared by software. 0: Normal mode. fCPU = fOSC / 2 1: Slow mode. fCPU is given by CP1, CP0 See low power consumption mode and MCC chapters for more details.
48/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
MISCELLANEOUS REGISTERS (Cont'd) MISCELLANEOUS REGISTER 2 (MISCR2) Read / Write Reset Value: 0000 0000 (00h)
7 BC1 BC0 SSM 0 SSI
Bit 7:6 = Reserved Must always be cleared Bit 5:4 = BC[1:0] Beep control These 2 bits select the PF1 pin beep capability.
Beep mode with fOSC=16MHz Off ~2 kHz ~1 kHz ~500 Hz Output Beep signal ~50% duty cycle BC1 BC0 0 0 1 1 0 1 0 1
The beep output signal is available in Active Halt mode but has to be disabled to reduce the consumption. Bit 3:2 = Reserved Must always be cleared Bit 1 = SSM SS mode selection It is set and cleared by software. 0: Normal mode - SS uses information coming from the SS pin of the SPI. 1: I/O mode, the SPI uses the information stored into bit SSI. Bit 0 = SSI SS internal mode This bit replaces pin SS of the SPI when bit SSM is set to 1. (see SPI description). It is set and cleared by software.
Table 11. Miscellaneous Register Map and Reset Values
Address (Hex.) 0020h 0040h Register Label MISCR1 Reset Value MISCR2 Reset Value 7 IS11 0 0 6 IS10 0 0 5 MCO 0 BC1 0 4 IS21 0 BC0 0 3 IS20 0 0 2 CP1 0 0 1 CP0 0 SSM 0 0 SMS 0 SSI 0
49/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13 ON-CHIP PERIPHERALS
13.1 WATCHDOG TIMER (WDG) 13.1.1 Introduction The Watchdog timer is used to detect the occurrence of a software fault, usually generated by external interference or by unforeseen logical conditions, which causes the application program to abandon its normal sequence. The Watchdog circuit generates an MCU reset on expiry of a programmed time period, unless the program refreshes the counter's contents before the T6 bit becomes cleared. 13.1.2 Main Features Programmable timer (64 increments of 12288 CPU cycles) Programmable reset Reset (if watchdog activated) after a HALT instruction or when the T6 bit reaches zero Figure 28. Watchdog Block Diagram

Hardware Watchdog selectable by option byte Watchdog Reset indicated by status flag (in versions with Safe Reset option only)
13.1.3 Functional Description The counter value stored in the CR register (bits T[6:0]), is decremented every 12288 machine cycles, and the length of the timeout period can be programmed by the user in 64 increments. If the watchdog is activated (the WDGA bit is set) and when the 7-bit timer (bits T[6:0]) rolls over from 40h to 3Fh (T6 becomes cleared), it initiates a reset cycle pulling low the RESET pin for typically 30s.
RESET
WATCHDOG CONTROL REGISTER (CR) WDGA T6 T5 T4 T3 T2 T1 T0
7-BIT DOWNCOUNTER
fCPU
CLOCK DIVIDER /12288
50/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
WATCHDOG TIMER (Cont'd) The application program must write in the CR register at regular intervals during normal operation to prevent an MCU reset. The value to be stored in the CR register must be between FFh and C0h (see Table 12 .Watchdog Timing (fCPU = 8 MHz)): - The WDGA bit is set (watchdog enabled) - The T6 bit is set to prevent generating an immediate reset - The T[5:0] bits contain the number of increments which represents the time delay before the watchdog produces a reset. Table 12.Watchdog Timing (fCPU = 8 MHz)
CR Register initial value Max Min FFh C0h WDG timeout period (ms) 98.304 1.536
13.1.7 Register Description CONTROL REGISTER (CR) Read / Write Reset Value: 0111 1111 (7F h)
7 WDGA T6 T5 T4 T3 T2 T1 0 T0
Bit 7 = WDGA Activation bit. This bit is set by software and only cleared by hardware after a reset. When WDGA = 1, the watchdog can generate a reset. 0: Watchdog disabled 1: Watchdog enabled Note: This bit is not used if the hardware watchdog option is enabled by option byte. Bit 6:0 = T[6:0] 7-bit timer (MSB to LSB). These bits contain the decremented value. A reset is produced when it rolls over from 40h to 3Fh (T6 becomes cleared). STATUS REGISTER (SR) Read / Write Reset Value*: 0000 0000 (00 h)
7 0 WDOGF
Notes: Following a reset, the watchdog is disabled. Once activated it cannot be disabled, except by a reset. The T6 bit can be used to generate a software reset (the WDGA bit is set and the T6 bit is cleared). If the watchdog is activated, the HALT instruction will generate a Reset. 13.1.4 Hardware Watchdog Option If Hardware Watchdog is selected by option byte, the watchdog is always active and the WDGA bit in the CR is not used. Refer to the device-specific Option Byte description. 13.1.5 Low Power Modes
Mode WAIT HALT Description No effect on Watchdog. Immediate reset generation as soon as the HALT instruction is executed if the Watchdog is activated (WDGA bit is set).
Bit 0 = WDOGF Watchdog flag. This bit is set by a watchdog reset and cleared by software or a power on/off reset. This bit is useful for distinguishing power/on off or external reset and watchdog reset. 0: No Watchdog reset occurred 1: Watchdog reset occurred * Only by software and power on/off reset Note: This register is not used in versions without LVD Reset.
13.1.6 Interrupts None.
51/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
WATCHDOG TIMER (Cont'd) Table 13. Watchdog Timer Register Map and Reset Values
Address (Hex.) 002Ah Register Label WDGCR Reset Value 7 WDGA 0 6 T6 1 5 T5 1 4 T4 1 3 T3 1 2 T2 1 1 T1 1 0 T0 1
52/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13.2 MAIN CLOCK CONTROLLER WITH REAL-TIME CLOCK TIMER (MCC/RTC) The Main Clock Controller consists of three different functions: a programmable CPU clock prescaler a clock-out signal to supply external devices a real-time clock timer with interrupt capability Each function can be used independently and simultaneously. 13.2.1 Programmable CPU clock prescaler The programmable CPU clock prescaler supplies the clock for the ST7 CPU and its internal peripherals. It manages Slow power saving mode (See Section 10.2 "SLOW MODE" on page 36 for more details). The prescaler selects the fCPU main clock frequency and is controlled by three bits in the MISCR1 register: CP[1:0] and SMS. CAUTION: The prescaler does not act on the CAN peripheral clock source. This peripheral is always supplied by the fOSC/2 clock source. 13.2.2 Clock-out capability The clock-out capability is an alternate function of an I/O port pin that outputs a fOSC/2 clock to drive external devices. It is controlled by the MCO bit in the MISCR1 register. CAUTION: When selected, the clock out pin suspends the clock during Active Halt mode. 13.2.3 Real-time clock timer (RTC) The counter of the real-time clock timer allows an interrupt to be generated based on an accurate real-time clock. Four different time bases depending directly on fOSC are available. The whole functionality is controlled by four bits of the MCCSR register: TB[1:0], OIE and OIF. When the RTC interrupt is enabled (OIE bit set), the ST7 enters Active Halt mode when the HALT instruction is executed. See Section 10.4 "ACTIVE HALT AND HALT MODES" on page 38 for more details.
Figure 29. Main Clock Controller (MCC/RTC) Block Diagram
PORT ALTERNATE FUNCTION
fOSC/2 MISCR1 -
MCO
MCO
-
-
CP1 CP0 SMS
fOSC
DIV 2 RTC COUNTER
DIV 2, 4, 8, 16 fCPU
CPU CLOCK TO CPU AND PERIPHERALS
MCCSR 0 0 0 0 TB1 TB0 OIE OIF
MCC/RTC INTERRUPT
53/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
MAIN CLOCK CONTROLLER WITH REAL-TIME CLOCK TIMER (Cont'd) MISCELLANEOUS REGISTER 1 (MISCR1) See Section 12 on page 47. MAIN CLOCK CONTROL/STATUS REGISTER (MCCSR) Read / Write Reset Value: 0000 0001 (01h)
7 0 0 0 0 TB1 TB0 OIE 0 OIF
Bit 0 = OIF Oscillator interrupt flag This bit is set by hardware and cleared by software reading the CSR register. It indicates when set that the main oscillator has measured the selected elapsed time (TB1:0). 0: Timeout not reached 1: Timeout reached CAUTION: The BRES and BSET instructions must not be used on the MCCSR register to avoid unintentionally clearing the OIF bit. 13.2.4 Low Power Modes
Mod
Bit 7:4 = Reserved, always read as 0.
WAIT
Bit 3:2 = TB[1:0] Time base control These bits select the programmable divider time base. They are set and cleared by software.
Counter Prescaler 32000 64000 160000 400000 Time Base TB1 fOSC =8MHz 4ms 8ms 20ms 50ms fOSC=16MHz 2ms 4ms 10ms 25ms 0 0 1 1 0 1 0 1 TB0
ACTIVE HALT
HALT
Description No effect on MCC/RTC peripheral. MCC/RTC interrupt cause the device to exit from Wait mode. No effect on MCC/RTC counter (OIE bit is set), the registers are frozen. MCC/RTC interrupt cause the device to exit from Active Halt mode. MCC/RTC counter and registers are frozen. MCC/RTC operation resumes when the MCU is woken up by an interrupt with "exit from Halt" capability.
A modification of the time base is taken into account at the end of the current period (previously set) to avoid unwanted time shift. This allows to use this time base as a real-time clock. Bit 1 = OIE Oscillator interrupt enable This bit set and cleared by software. 0: Oscillator interrupt disabled 1: Oscillator interrupt enabled This interrupt allows to exit from Active Halt mode. When this bit is set, calling the ST7 software HALT instruction enters the Active Halt power saving mode.
13.2.5 Interrupts The MCC/RTC interrupt event generates an interrupt if the OIE bit of the MCCSR register is set and the interrupt mask in the CC register is not active (RIM instruction).
Interrupt Event Time base overflow event Enable Event Control Flag Bit OIF OIE Exit from Wait Yes Exit from Halt No 1)
Notes: 1. The MCC/RTC interrupt allows to exit from Active Halt mode, not from Halt mode.
Table 14. MCC Register Map and Reset Values
Address (Hex.) 0029h Register Label MCCSR Reset Value 7 6 5 4 3 TB1 0 2 TB0 0 1 OIE 0 0 OIF 1
0
0
0
0
54/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13.3 16-BIT TIMER 13.3.1 Introduction The timer consists of a 16-bit free-running counter driven by a programmable prescaler. It may be used for a variety of purposes, including measuring the pulse lengths of up to two input signals (input capture) or generating up to two output waveforms (output compare and PWM). Pulse lengths and waveform periods can be modulated from a few microseconds to several milliseconds using the timer prescaler and the CPU clock prescaler. Some ST7 devices have two on-chip 16-bit timers. They are completely independent, and do not share any resources. They are synchronized after a MCU reset as long as the timer clock frequencies are not modified. This description covers one or two 16-bit timers. In ST7 devices with two timers, register names are prefixed with TA (Timer A) or TB (Timer B). 13.3.2 Main Features Programmable prescaler: fCPU divided by 2, 4 or 8 Overflow status flag and maskable interrupt External clock input (must be at least 4 times slower than the CPU clock speed) with the choice of active edge Output compare functions with: - 2 dedicated 16-bit registers - 2 dedicated programmable signals - 2 dedicated status flags - 1 dedicated maskable interrupt Input capture functions with: - 2 dedicated 16-bit registers - 2 dedicated active edge selection signals - 2 dedicated status flags - 1 dedicated maskable interrupt Pulse Width Modulation mode (PWM) One Pulse mode 5 alternate functions on I/O ports (ICAP1, ICAP2, OCMP1, OCMP2, EXTCLK)* The Block Diagram is shown in Figure 30. *Note: Some timer pins may not be available (not bonded) in some ST7 devices. Refer to the device pin out description. When reading an input signal on a non-bonded pin, the value will always be `1'. 13.3.3 Functional Description 13.3.3.1 Counter The main block of the Programmable Timer is a 16-bit free running upcounter and its associated 16-bit registers. The 16-bit registers are made up of two 8-bit registers called high and low. Counter Register (CR) - Counter High Register (CHR) is the most significant byte (MS Byte). - Counter Low Register (CLR) is the least significant byte (LS Byte). Alternate Counter Register (ACR) - Alternate Counter High Register (ACHR) is the most significant byte (MS Byte). - Alternate Counter Low Register (ACLR) is the least significant byte (LS Byte). These two read-only 16-bit registers contain the same value but with the difference that reading the ACLR register does not clear the TOF bit (Timer overflow flag), located in the Status register (SR). (See note at the end of paragraph titled 16-bit read sequence). Writing in the CLR register or ACLR register resets the free running counter to the FFFCh value. Both counters have a reset value of FFFCh (this is the only value which is reloaded in the 16-bit timer). The reset value of both counters is also FFFCh in One Pulse mode and PWM mode. The timer clock depends on the clock control bits of the CR2 register, as illustrated in Table 15 Clock Control Bits. The value in the counter register repeats every 131072, 262144 or 524288 CPU clock cycles depending on the CC[1:0] bits. The timer frequency can be fCPU/2, fCPU/4, fCPU/8 or an external frequency.
55/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Figure 30. Timer Block Diagram
ST7 INTERNAL BUS fCPU MCU-PERIPHERAL INTERFACE 8 low 8-bit buffer EXEDG 16 1/2 1/4 1/8 EXTCLK pin COUNTER REGISTER ALTERNATE COUNTER REGISTER 16 CC[1:0] TIMER INTERNAL BUS 16 16 OVERFLOW DETECT CIRCUIT OUTPUT COMPARE REGISTER 1 OUTPUT COMPARE REGISTER 2 INPUT CAPTURE REGISTER 1 16 INPUT CAPTURE REGISTER 2 16 8 high low 8 high 8 low 8 high 8 low 8 high 8 low 8
8 high
OUTPUT COMPARE CIRCUIT 6
EDGE DETECT CIRCUIT1
ICAP1 pin
EDGE DETECT CIRCUIT2
ICAP2 pin
LATCH1
ICF1 OCF1 TOF ICF2 OCF2 0
OCMP1 pin OCMP2 pin
0
0 LATCH2
(Status Register) SR
ICIE OCIE TOIE FOLV2 FOLV1 OLVL2 IEDG1 OLVL1
OC1E OC2E OPM PWM
CC1
CC0 IEDG2 EXEDG
(Control Register 1) CR1
(Control Register 2) CR2
(See note) TIMER INTERRUPT
Note: If IC, OC and TO interrupt requests have separate vectors then the last OR is not present (See device Interrupt Vector Table)
56/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 16-bit Read Sequence: (from either the Counter Register or the Alternate Counter Register). Beginning of the sequence At t0 Read MS Byte Other instructions Read At t0 +t LS Byte Sequence completed The user must read the MS Byte first, then the LS Byte value is buffered automatically. This buffered value remains unchanged until the 16-bit read sequence is completed, even if the user reads the MS Byte several times. After a complete reading sequence, if only the CLR register or ACLR register are read, they return the LS Byte of the count value at the time of the read. Whatever the timer mode used (input capture, output compare, One Pulse mode or PWM mode) an overflow occurs when the counter rolls over from FFFFh to 0000h then: - The TOF bit of the SR register is set. - A timer interrupt is generated if: - TOIE bit of the CR1 register is set and - I bit of the CC register is cleared. If one of these conditions is false, the interrupt remains pending to be issued as soon as they are both true.
Returns the buffered
LS Byte is buffered
LS Byte value at t0
Clearing the overflow interrupt request is done in two steps: 1. Reading the SR register while the TOF bit is set. 2. An access (read or write) to the CLR register. Note: The TOF bit is not cleared by accessing the ACLR register. The advantage of accessing the ACLR register rather than the CLR register is that it allows simultaneous use of the overflow function and reading the free running counter at random times (for example, to measure elapsed time) without the risk of clearing the TOF bit erroneously. The timer is not affected by Wait mode. In Halt mode, the counter stops counting until the mode is exited. Counting then resumes from the previous count (MCU awakened by an interrupt) or from the reset count (MCU awakened by a Reset). 13.3.3.2 External Clock The external clock (where available) is selected if CC0 = 1 and CC1 = 1 in the CR2 register. The status of the EXEDG bit in the CR2 register determines the type of level transition on the external clock pin EXTCLK that will trigger the free running counter. The counter is synchronized with the falling edge of the internal CPU clock. A minimum of four falling edges of the CPU clock must occur between two consecutive active edges of the external clock; thus the external clock frequency must be less than a quarter of the CPU clock frequency.
57/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Figure 31. Counter Timing Diagram, internal clock divided by 2
CPU CLOCK INTERNAL RESET TIMER CLOCK COUNTER REGISTER TIMER OVERFLOW FLAG (TOF) FFFD FFFE FFFF 0000 0001 0002 0003
Figure 32. Counter Timing Diagram, internal clock divided by 4
CPU CLOCK INTERNAL RESET TIMER CLOCK COUNTER REGISTER TIMER OVERFLOW FLAG (TOF) FFFC FFFD 0000 0001
Figure 33. Counter Timing Diagram, internal clock divided by 8
CPU CLOCK INTERNAL RESET TIMER CLOCK COUNTER REGISTER TIMER OVERFLOW FLAG (TOF) FFFC FFFD 0000
Note: The MCU is in reset state when the internal reset signal is high. When it is low, the MCU is running.
58/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 13.3.3.3 Input Capture In this section, the index, i, may be 1 or 2 because there are two input capture functions in the 16-bit timer. The two input capture 16-bit registers (IC1R and IC2R) are used to latch the value of the free running counter after a transition is detected by the ICAPi pin (see Figure 34).
ICiR MS Byte ICiHR LS Byte ICiLR
The ICiR register is a read-only register. The active transition is software programmable through the IEDGi bit of Control Registers (CRi). Timing resolution is one count of the free running counter: (fCPU/CC[1:0]). Procedure: To use the input capture function, select the following in the CR2 register: - Select the timer clock (CC[1:0]) (see Table 15 Clock Control Bits). - Select the edge of the active transition on the ICAP2 pin with the IEDG2 bit (the ICAP2 pin must be configured as a floating input or input with pull-up without interrupt if this configuration is available). And select the following in the CR1 register: - Set the ICIE bit to generate an interrupt after an input capture coming from either the ICAP1 pin or the ICAP2 pin - Select the edge of the active transition on the ICAP1 pin with the IEDG1 bit (the ICAP1 pin must be configured as a floating input or input with pull-up without interrupt if this configuration is available).
When an input capture occurs: - The ICFi bit is set. - The ICiR register contains the value of the free running counter on the active transition on the ICAPi pin (see Figure 35). - A timer interrupt is generated if the ICIE bit is set and the I bit is cleared in the CC register. Otherwise, the interrupt remains pending until both conditions become true. Clearing the Input Capture interrupt request (i.e. clearing the ICFi bit) is done in two steps: 1. Reading the SR register while the ICFi bit is set. 2. An access (read or write) to the ICiLR register. Notes: 1. After reading the ICiHR register, the transfer of input capture data is inhibited and ICFi will never be set until the ICiLR register is also read. 2. The ICiR register contains the free running counter value which corresponds to the most recent input capture. 3. The two input capture functions can be used together even if the timer also uses the two output compare functions. 4. In One Pulse mode and PWM mode only the input capture 2 function can be used. 5. The alternate inputs (ICAP1 and ICAP2) are always directly connected to the timer. So any transitions on these pins activate the input capture function. Moreover if one of the ICAPi pin is configured as an input and the second one as an output, an interrupt can be generated if the user toggles the output pin and if the ICIE bit is set. This can be avoided if the input capture function i is disabled by reading the ICiHR (see note 1). 6. The TOF bit can be used with an interrupt in order to measure events that exceed the timer range (FFFFh).
59/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Figure 34. Input Capture Block Diagram
ICAP1 pin ICAP2 pin EDGE DETECT CIRCUIT2 EDGE DETECT CIRCUIT1
ICIE
(Control Register 1) CR1
IEDG1
(Status Register) SR IC2R Register IC1R Register
ICF1 ICF2 0 0 0
16-BIT
(Control Register 2) CR2
CC1 CC0 IEDG2
16-BIT FREE RUNNING
COUNTER
Figure 35. Input Capture Timing Diagram
TIMER CLOCK COUNTER REGISTER ICAPi PIN ICAPi FLAG ICAPi REGISTER Note: Active edge is rising edge. FF03 FF01 FF02 FF03
60/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 13.3.3.4 Output Compare In this section, the index, i, may be 1 or 2 because there are two output compare functions in the 16bit timer. This function can be used to control an output waveform or indicate when a period of time has elapsed. When a match is found between the Output Compare register and the free running counter, the output compare function: - Assigns pins with a programmable value if the OCiE bit is set - Sets a flag in the status register - Generates an interrupt if enabled Two 16-bit registers Output Compare Register 1 (OC1R) and Output Compare Register 2 (OC2R) contain the value to be compared to the counter register each timer clock cycle.
OCiR MS Byte OCiHR LS Byte OCiLR
- The OCMPi pin takes OLVLi bit value (OCMPi pin latch is forced low during reset). - A timer interrupt is generated if the OCIE bit is set in the CR1 register and the I bit is cleared in the CC register (CC). The OCiR register value required for a specific timing application can be calculated using the following formula:
OCiR =
Where:
t * fCPU
PRESC
t
= Output compare period (in seconds) fCPU = CPU clock frequency (in hertz) = Timer prescaler factor (2, 4 or 8 dePRESC pending on CC[1:0] bits, see Table 15 Clock Control Bits) If the timer clock is an external clock, the formula is:
These registers are readable and writable and are not affected by the timer hardware. A reset event changes the OCiR value to 8000h. Timing resolution is one count of the free running counter: (fCPU/CC[1:0]). Procedure: To use the output compare function, select the following in the CR2 register: - Set the OCiE bit if an output is needed then the OCMPi pin is dedicated to the output compare i signal. - Select the timer clock (CC[1:0]) (see Table 15 Clock Control Bits). And select the following in the CR1 register: - Select the OLVLi bit to applied to the OCMPi pins after the match occurs. - Set the OCIE bit to generate an interrupt if it is needed. When a match is found between OCRi register and CR register: - OCFi bit is set.
OCiR = t * fEXT
Where:
t
fEXT
= Output compare period (in seconds) = External timer clock frequency (in hertz)
Clearing the output compare interrupt request (i.e. clearing the OCFi bit) is done by: 1. Reading the SR register while the OCFi bit is set. 2. An access (read or write) to the OCiLR register. The following procedure is recommended to prevent the OCFi bit from being set between the time it is read and the write to the OCiR register: - Write to the OCiHR register (further compares are inhibited). - Read the SR register (first step of the clearance of the OCFi bit, which may be already set). - Write to the OCiLR register (enables the output compare function and clears the OCFi bit).
61/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Notes: 1. After a processor write cycle to the OCiHR register, the output compare function is inhibited until the OCiLR register is also written. 2. If the OCiE bit is not set, the OCMPi pin is a general I/O port and the OLVLi bit will not appear when a match is found but an interrupt could be generated if the OCIE bit is set. 3. When the timer clock is fCPU/2, OCFi and OCMPi are set while the counter value equals the OCiR register value (see Figure 37 on page 63). This behavior is the same in OPM or PWM mode. When the timer clock is fCPU/4, fCPU/8 or in external clock mode, OCFi and OCMPi are set while the counter value equals the OCiR register value plus 1 (see Figure 38 on page 63). 4. The output compare functions can be used both for generating external events on the OCMPi pins even if the input capture mode is also used. 5. The value in the 16-bit OCiR register and the OLVi bit should be changed after each successful comparison in order to control an output waveform or establish a new elapsed timeout. Figure 36. Output Compare Block Diagram
Forced Compare Output capability When the FOLVi bit is set by software, the OLVLi bit is copied to the OCMPi pin. The OLVi bit has to be toggled in order to toggle the OCMPi pin when it is enabled (OCiE bit = 1). The OCFi bit is then not set by hardware, and thus no interrupt request is generated. FOLVLi bits have no effect in either One Pulse mode or PWM mode.
16 BIT FREE RUNNING COUNTER 16-bit OUTPUT COMPARE CIRCUIT 16-bit 16-bit
OC1E OC2E
CC1
CC0
(Control Register 2) CR2 (Control Register 1) CR1
OCIE FOLV2 FOLV1 OLVL2 OLVL1 Latch 1
OCMP1 Pin OCMP2 Pin
OC1R Register
OCF1 OCF2 0 0 0
Latch 2
OC2R Register (Status Register) SR
62/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Figure 37. Output Compare Timing Diagram, fTIMER = fCPU/2
INTERNAL CPU CLOCK TIMER CLOCK COUNTER REGISTER OUTPUT COMPARE REGISTER i (OCRi) OUTPUT COMPARE FLAG i (OCFi) OCMPi PIN (OLVLi = 1) 2ECF 2ED0 2ED1 2ED2 2ED3 2ED4 2ED3
Figure 38. Output Compare Timing Diagram, fTIMER = fCPU/4
INTERNAL CPU CLOCK TIMER CLOCK COUNTER REGISTER OUTPUT COMPARE REGISTER i (OCRi) COMPARE REGISTER i LATCH OUTPUT COMPARE FLAG i (OCFi) OCMPi PIN (OLVLi = 1) 2ECF 2ED0 2ED1 2ED2 2ED3 2ED4 2ED3
63/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 13.3.3.5 One Pulse Mode One Pulse mode enables the generation of a pulse when an external event occurs. This mode is selected via the OPM bit in the CR2 register. The One Pulse mode uses the Input Capture1 function and the Output Compare1 function. Procedure: To use One Pulse mode: 1. Load the OC1R register with the value corresponding to the length of the pulse (see the formula in the opposite column). 2. Select the following in the CR1 register: - Using the OLVL1 bit, select the level to be applied to the OCMP1 pin after the pulse. - Using the OLVL2 bit, select the level to be applied to the OCMP1 pin during the pulse. - Select the edge of the active transition on the ICAP1 pin with the IEDG1 bit (the ICAP1 pin must be configured as floating input). 3. Select the following in the CR2 register: - Set the OC1E bit, the OCMP1 pin is then dedicated to the Output Compare 1 function. - Set the OPM bit. - Select the timer clock CC[1:0] (see Table 15 Clock Control Bits).
Clearing the Input Capture interrupt request (i.e. clearing the ICFi bit) is done in two steps: 1. Reading the SR register while the ICFi bit is set. 2. An access (read or write) to the ICiLR register. The OC1R register value required for a specific timing application can be calculated using the following formula: OCiR Value =
t * fCPU
PRESC
-5
Where: t = Pulse period (in seconds) fCPU = CPU clock frequency (in hertz) PRESC = Timer prescaler factor (2, 4 or 8 depending on the CC[1:0] bits, see Table 15 Clock Control Bits) If the timer clock is an external clock the formula is: OCiR = t * fEXT -5 Where: t = Pulse period (in seconds) fEXT = External timer clock frequency (in hertz) When the value of the counter is equal to the value of the contents of the OC1R register, the OLVL1 bit is output on the OCMP1 pin (see Figure 39). Notes: 1. The OCF1 bit cannot be set by hardware in One Pulse mode but the OCF2 bit can generate an Output Compare interrupt. 2. When the Pulse Width Modulation (PWM) and One Pulse mode (OPM) bits are both set, the PWM mode is the only active one. 3. If OLVL1 = OLVL2 a continuous signal will be seen on the OCMP1 pin. 4. The ICAP1 pin can not be used to perform input capture. The ICAP2 pin can be used to perform input capture (ICF2 can be set and IC2R can be loaded) but the user must take care that the counter is reset each time a valid edge occurs on the ICAP1 pin and ICF1 can also generates interrupt if ICIE is set. 5. When One Pulse mode is used OC1R is dedicated to this mode. Nevertheless OC2R and OCF2 can be used to indicate that a period of time has elapsed but cannot generate an output waveform because the OLVL2 level is dedicated to One Pulse mode.
One Pulse mode cycle When event occurs on ICAP1 OCMP1 = OLVL2 Counter is reset to FFFCh ICF1 bit is set When Counter = OC1R
OCMP1 = OLVL1
Then, on a valid event on the ICAP1 pin, the counter is initialized to FFFCh and the OLVL2 bit is loaded on the OCMP1 pin, the ICF1 bit is set and the value FFFDh is loaded in the IC1R register. Because the ICF1 bit is set when an active edge occurs, an interrupt can be generated if the ICIE bit is set.
64/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Figure 39. One Pulse Mode Timing Example
COUNTER ICAP1 OCMP1
FFFC FFFD FFFE
2ED0 2ED1 2ED2 2ED3
FFFC FFFD
OLVL2
OLVL1
OLVL2
compare1 Note: IEDG1 = 1, OC1R = 2ED0h, OLVL1 = 0, OLVL2 = 1
Figure 40. Pulse Width Modulation Mode Timing Example
COUNTER 34E2 FFFC FFFD FFFE OCMP1 OLVL2
2ED0 2ED1 2ED2
34E2
FFFC
OLVL1
OLVL2
compare2
compare1
compare2
Note: OC1R = 2ED0h, OC2R = 34E2, OLVL1 = 0, OLVL2 = 1
65/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 13.3.3.6 Pulse Width Modulation Mode Pulse Width Modulation (PWM) mode enables the generation of a signal with a frequency and pulse length determined by the value of the OC1R and OC2R registers. The Pulse Width Modulation mode uses the complete Output Compare 1 function plus the OC2R register, and so these functions cannot be used when the PWM mode is activated. Procedure To use Pulse Width Modulation mode: 1. Load the OC2R register with the value corresponding to the period of the signal using the formula in the opposite column. 2. Load the OC1R register with the value corresponding to the period of the pulse if OLVL1 = 0 and OLVL2 = 1, using the formula in the opposite column. 3. Select the following in the CR1 register: - Using the OLVL1 bit, select the level to be applied to the OCMP1 pin after a successful comparison with OC1R register. - Using the OLVL2 bit, select the level to be applied to the OCMP1 pin after a successful comparison with OC2R register. 4. Select the following in the CR2 register: - Set OC1E bit: the OCMP1 pin is then dedicated to the output compare 1 function. - Set the PWM bit. - Select the timer clock (CC[1:0]) (see Table 15 Clock Control Bits). If OLVL1 = 1 and OLVL2 = 0, the length of the positive pulse is the difference between the OC2R and OC1R registers. If OLVL1 = OLVL2 a continuous signal will be seen on the OCMP1 pin. Pulse Width Modulation cycle When Counter = OC1R
The OCiR register value required for a specific timing application can be calculated using the following formula: OCiR Value =
t * fCPU
PRESC
-5
Where: t = Signal or pulse period (in seconds) fCPU = CPU clock frequency (in hertz) PRESC = Timer prescaler factor (2, 4 or 8 depending on CC[1:0] bits, see Table 15 Clock Control Bits) If the timer clock is an external clock the formula is: OCiR = t * fEXT -5 Where: t = Signal or pulse period (in seconds) fEXT = External timer clock frequency (in hertz) The Output Compare 2 event causes the counter to be initialized to FFFCh (See Figure 40) Notes: 1. After a write instruction to the OCiHR register, the output compare function is inhibited until the OCiLR register is also written. 2. The OCF1 and OCF2 bits cannot be set by hardware in PWM mode, therefore the Output Compare interrupt is inhibited. 3. The ICF1 bit is set by hardware when the counter reaches the OC2R value and can produce a timer interrupt if the ICIE bit is set and the I bit is cleared. 4. In PWM mode the ICAP1 pin can not be used to perform input capture because it is disconnected from the timer. The ICAP2 pin can be used to perform input capture (ICF2 can be set and IC2R can be loaded) but the user must take care that the counter is reset after each period and ICF1 can also generate an interrupt if ICIE is set. 5. When the Pulse Width Modulation (PWM) and One Pulse mode (OPM) bits are both set, the PWM mode is the only active one.
OCMP1 = OLVL1
When Counter = OC2R
OCMP1 = OLVL2 Counter is reset to FFFCh ICF1 bit is set
66/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 13.3.4 Low Power Modes
Mode WAIT No effect on 16-bit Timer. Timer interrupts cause the device to exit from Wait mode. 16-bit Timer registers are frozen. In Halt mode, the counter stops counting until Halt mode is exited. Counting resumes from the previous count when the MCU is woken up by an interrupt with "exit from Halt mode" capability or from the counter reset value when the MCU is woken up by a RESET. If an input capture event occurs on the ICAPi pin, the input capture detection circuitry is armed. Consequently, when the MCU is woken up by an interrupt with "exit from Halt mode" capability, the ICFi bit is set, and the counter value present when exiting from Halt mode is captured into the ICiR register. Description
HALT
13.3.5 Interrupts
Interrupt Event Input Capture 1 event/Counter reset in PWM mode Input Capture 2 event Output Compare 1 event (not available in PWM mode) Output Compare 2 event (not available in PWM mode) Timer Overflow event Event Flag ICF1 ICF2 OCF1 OCF2 TOF Enable Control Bit ICIE OCIE TOIE Exit from Wait Yes Yes Yes Yes Yes Exit from Halt No No No No No
Note: The 16-bit Timer interrupt events are connected to the same interrupt vector (see INTERRUPTS chapter). These events generate an interrupt if the corresponding Enable Control Bit is set and the interrupt mask in the CC register is reset (RIM instruction). 13.3.6 Summary of Timer modes
Modes Input Capture (1 and/or 2) Output Compare (1 and/or 2) One Pulse mode PWM Mode Input Capture 1 Yes Yes No No Available Resources Input Capture 2 Output Compare 1 Output Compare 2 Yes Yes Yes Yes Yes Yes Not Recommended1) No Partially 2) Not Recommended3) No No
Notes: 1. See note 4 in Section 13.3.3.5 "One Pulse Mode" on page 64 2. See note 5 in Section 13.3.3.5 "One Pulse Mode" on page 64 3. See note 4 in Section 13.3.3.6 "Pulse Width Modulation Mode" on page 66
67/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) 13.3.7 Register Description Each Timer is associated with three control and status registers, and with six pairs of data registers (16-bit values) relating to the two input captures, the two output compares, the counter and the alternate counter. CONTROL REGISTER 1 (CR1) Read/Write Reset Value: 0000 0000 (00h)
7 0
Bit 4 = FOLV2 Forced Output Compare 2. This bit is set and cleared by software. 0: No effect on the OCMP2 pin. 1: Forces the OLVL2 bit to be copied to the OCMP2 pin, if the OC2E bit is set and even if there is no successful comparison. Bit 3 = FOLV1 Forced Output Compare 1. This bit is set and cleared by software. 0: No effect on the OCMP1 pin. 1: Forces OLVL1 to be copied to the OCMP1 pin, if the OC1E bit is set and even if there is no successful comparison. Bit 2 = OLVL2 Output Level 2. This bit is copied to the OCMP2 pin whenever a successful comparison occurs with the OC2R register and OCxE is set in the CR2 register. This value is copied to the OCMP1 pin in One Pulse mode and Pulse Width Modulation mode. Bit 1 = IEDG1 Input Edge 1. This bit determines which type of level transition on the ICAP1 pin will trigger the capture. 0: A falling edge triggers the capture. 1: A rising edge triggers the capture. Bit 0 = OLVL1 Output Level 1. The OLVL1 bit is copied to the OCMP1 pin whenever a successful comparison occurs with the OC1R register and the OC1E bit is set in the CR2 register.
ICIE OCIE TOIE FOLV2 FOLV1 OLVL2 IEDG1 OLVL1
Bit 7 = ICIE Input Capture Interrupt Enable. 0: Interrupt is inhibited. 1: A timer interrupt is generated whenever the ICF1 or ICF2 bit of the SR register is set. Bit 6 = OCIE Output Compare Interrupt Enable. 0: Interrupt is inhibited. 1: A timer interrupt is generated whenever the OCF1 or OCF2 bit of the SR register is set. Bit 5 = TOIE Timer Overflow Interrupt Enable. 0: Interrupt is inhibited. 1: A timer interrupt is enabled whenever the TOF bit of the SR register is set.
68/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) CONTROL REGISTER 2 (CR2) Read/Write Reset Value: 0000 0000 (00h)
7 0
OC1E OC2E OPM PWM CC1 CC0 IEDG2 EXEDG
Bit 4 = PWM Pulse Width Modulation. 0: PWM mode is not active. 1: PWM mode is active, the OCMP1 pin outputs a programmable cyclic signal; the length of the pulse depends on the value of OC1R register; the period depends on the value of OC2R register. Bits 3:2 = CC[1:0] Clock Control. The timer clock mode depends on these bits: Table 15. Clock Control Bits
Timer Clock fCPU / 4 fCPU / 2 fCPU / 8 External Clock (where available) CC1 0 0 1 1 CC0 0 1 0 1
Bit 7 = OC1E Output Compare 1 Pin Enable. This bit is used only to output the signal from the timer on the OCMP1 pin (OLV1 in Output Compare mode, both OLV1 and OLV2 in PWM and One Pulse mode). Whatever the value of the OC1E bit, the internal Output Compare 1 function of the timer remains active. 0: OCMP1 pin alternate function disabled (I/O pin free for general-purpose I/O). 1: OCMP1 pin alternate function enabled. Bit 6 = OC2E Output Compare 2 Pin Enable. This bit is used only to output the signal from the timer on the OCMP2 pin (OLV2 in Output Compare mode). Whatever the value of the OC2E bit, the internal Output Compare 2 function of the timer remains active. 0: OCMP2 pin alternate function disabled (I/O pin free for general-purpose I/O). 1: OCMP2 pin alternate function enabled. Bit 5 = OPM One Pulse mode. 0: One Pulse mode is not active. 1: One Pulse mode is active, the ICAP1 pin can be used to trigger one pulse on the OCMP1 pin; the active transition is given by the IEDG1 bit. The length of the generated pulse depends on the contents of the OC1R register.
Note: If the external clock pin is not available, programming the external clock configuration stops the counter. Bit 1 = IEDG2 Input Edge 2. This bit determines which type of level transition on the ICAP2 pin will trigger the capture. 0: A falling edge triggers the capture. 1: A rising edge triggers the capture. Bit 0 = EXEDG External Clock Edge. This bit determines which type of level transition on the external clock pin (EXTCLK) will trigger the counter register. 0: A falling edge triggers the counter register. 1: A rising edge triggers the counter register.
69/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) STATUS REGISTER (SR) Read Only Reset Value: 0000 0000 (00h) The three least significant bits are not used.
7 ICF1 OCF1 TOF ICF2 OCF2 0 0 0 0
INPUT CAPTURE 1 HIGH REGISTER (IC1HR) Read Only Reset Value: Undefined This is an 8-bit read only register that contains the high part of the counter value (transferred by the input capture 1 event).
7 MSB 0 LSB
Bit 7 = ICF1 Input Capture Flag 1. 0: No input capture (reset value). 1: An input capture has occurred on the ICAP1 pin or the counter has reached the OC2R value in PWM mode. To clear this bit, first read the SR register, then read or write the low byte of the IC1R (IC1LR) register. Bit 6 = OCF1 Output Compare Flag 1. 0: No match (reset value). 1: The content of the free running counter matches the content of the OC1R register. To clear this bit, first read the SR register, then read or write the low byte of the OC1R (OC1LR) register. Bit 5 = TOF Timer Overflow Flag. 0: No timer overflow (reset value). 1: The free running counter has rolled over from FFFFh to 0000h. To clear this bit, first read the SR register, then read or write the low byte of the CR (CLR) register. Note: Reading or writing the ACLR register does not clear TOF. Bit 4 = ICF2 Input Capture Flag 2. 0: No input capture (reset value). 1: An input capture has occurred on the ICAP2 pin. To clear this bit, first read the SR register, then read or write the low byte of the IC2R (IC2LR) register. Bit 3 = OCF2 Output Compare Flag 2. 0: No match (reset value). 1: The content of the free running counter matches the content of the OC2R register. To clear this bit, first read the SR register, then read or write the low byte of the OC2R (OC2LR) register. Bit 2-0 = Reserved, forced by hardware to 0.
INPUT CAPTURE 1 LOW REGISTER (IC1LR) Read Only Reset Value: Undefined This is an 8-bit read only register that contains the low part of the counter value (transferred by the input capture 1 event).
7 MSB 0 LSB
OUTPUT COMPARE 1 HIGH REGISTER (OC1HR) Read/Write Reset Value: 1000 0000 (80h) This is an 8-bit register that contains the high part of the value to be compared to the CHR register.
7 MSB 0 LSB
OUTPUT COMPARE 1 LOW REGISTER (OC1LR) Read/Write Reset Value: 0000 0000 (00h) This is an 8-bit register that contains the low part of the value to be compared to the CLR register.
7 MSB 0 LSB
70/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) OUTPUT COMPARE 2 HIGH REGISTER (OC2HR) Read/Write Reset Value: 1000 0000 (80h) This is an 8-bit register that contains the high part of the value to be compared to the CHR register.
7 MSB 0 LSB
ALTERNATE COUNTER HIGH REGISTER (ACHR) Read Only Reset Value: 1111 1111 (FFh) This is an 8-bit register that contains the high part of the counter value.
7 MSB 0 LSB
OUTPUT COMPARE 2 LOW REGISTER (OC2LR) Read/Write Reset Value: 0000 0000 (00h) This is an 8-bit register that contains the low part of the value to be compared to the CLR register.
7 MSB 0 LSB
ALTERNATE COUNTER LOW REGISTER (ACLR) Read Only Reset Value: 1111 1100 (FCh) This is an 8-bit register that contains the low part of the counter value. A write to this register resets the counter. An access to this register after an access to SR register does not clear the TOF bit in SR register.
7 0 LSB
COUNTER HIGH REGISTER (CHR) Read Only Reset Value: 1111 1111 (FFh) This is an 8-bit register that contains the high part of the counter value.
7 MSB 0 LSB
MSB
INPUT CAPTURE 2 HIGH REGISTER (IC2HR) Read Only Reset Value: Undefined This is an 8-bit read only register that contains the high part of the counter value (transferred by the Input Capture 2 event).
7 0 LSB
COUNTER LOW REGISTER (CLR) Read Only Reset Value: 1111 1100 (FCh) This is an 8-bit register that contains the low part of the counter value. A write to this register resets the counter. An access to this register after accessing the SR register clears the TOF bit.
7 MSB 0 LSB
MSB
INPUT CAPTURE 2 LOW REGISTER (IC2LR) Read Only Reset Value: Undefined This is an 8-bit read only register that contains the low part of the counter value (transferred by the Input Capture 2 event).
7 MSB 0 LSB
71/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16-BIT TIMER (Cont'd) Table 16. 16-Bit Timer Register Map and Reset Values
Address (Hex.) Register Label 7 ICIE 0 OC1E 0 ICF1 0 MSB MSB MSB MSB MSB MSB MSB 1 MSB 1 MSB 1 MSB 1 MSB MSB 6 OCIE 0 OC2E 0 OCF1 0 5 TOIE 0 OPM 0 TOF 0 4 FOLV2 0 PWM 0 ICF2 0 3 FOLV1 0 CC1 0 OCF2 0 2 OLVL2 0 CC0 0 0 1 IEDG1 0 IEDG2 0 0 0 OLVL1 0 EXEDG 0 0 LSB LSB LSB LSB LSB LSB LSB 1 LSB 0 LSB 1 LSB 0 LSB LSB -
Timer A: 32 CR1 Timer B: 42 Reset Value Timer A: 31 CR2 Timer B: 41 Reset Value Timer A: 33 SR Timer B: 43 Reset Value Timer A: 34 ICHR1 Timer B: 44 Reset Value Timer A: 35 ICLR1 Timer B: 45 Reset Value Timer A: 36 OCHR1 Timer B: 46 Reset Value Timer A: 37 OCLR1 Timer B: 47 Reset Value Timer A: 3E OCHR2 Timer B: 4E Reset Value Timer A: 3F OCLR2 Timer B: 4F Reset Value Timer A: 38 CHR Timer B: 48 Reset Value Timer A: 39 CLR Timer B: 49 Reset Value Timer A: 3A ACHR Timer B: 4A Reset Value Timer A: 3B ACLR Timer B: 4B Reset Value Timer A: 3C ICHR2 Timer B: 4C Reset Value Timer A: 3D ICLR2 Timer B: 4D Reset Value
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1
1
1
1
1
1
1
1
1
1
1
0
1
1
1
1
1
1
1 -
1 -
1 -
1 -
1 -
0 -
-
-
-
-
-
-
72/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13.4 SERIAL PERIPHERAL INTERFACE (SPI) 13.4.1 Introduction The Serial Peripheral Interface (SPI) allows fullduplex, synchronous, serial communication with external devices. An SPI system may consist of a master and one or more slaves or a system in which devices may be either masters or slaves. The SPI is normally used for communication between the microcontroller and external peripherals or another microcontroller. Refer to the PIN DESCRIPTION chapter for the device-specific pinout. 13.4.2 Main Features Full duplex, three-wire synchronous transfers Master or slave operation 4 master mode frequencies Maximum slave mode frequency = fCPU/4 4 programmable master bit rates Programmable clock polarity and phase End of transfer interrupt flag Write collision flag protection Master mode fault protection capability 13.4.3 General description The SPI is connected to external devices through four alternate pins: - MISO: Master In Slave Out pin - MOSI: Master Out Slave In pin - SCK: Serial Clock pin - SS: Slave select pin A basic example of interconnections between a single master and a single slave is illustrated on Figure 41. The MOSI pins are connected together as are MISO pins. In this way data is transferred serially between master and slave (most significant bit first). When the master device transmits data to a slave device via MOSI pin, the slave device responds by sending data to the master device via the MISO pin. This implies full duplex transmission with both data out and data in synchronized with the same clock signal (which is provided by the master device via the SCK pin). Thus, the byte transmitted is replaced by the byte received and eliminates the need for separate transmit-empty and receiver-full bits. A status flag is used to indicate that the I/O operation is complete. Four possible data/clock timing relationships may be chosen (see Figure 44) but master and slave must be programmed with the same timing mode.
Figure 41. Serial Peripheral Interface Master/Slave
MASTER MSBit LSBit MISO MISO MSBit SLAVE LSBit
8-BIT SHIFT REGISTER
8-BIT SHIFT REGISTER
MOSI
MOSI
SPI CLOCK GENERATOR
SCK
SCK +5V
SS
SS
73/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) Figure 42. Serial Peripheral Interface Block Diagram
Internal Bus Read Read Buffer
DR IT request
MOSI MISO
8-Bit Shift Register
SPIF WCOL - MODF -
SR
-
Write SPI STATE CONTROL
SCK SS
CR
SPIE SPE SPR2 MSTR CPOL CPHA SPR1 SPR0
MASTER CONTROL
SERIAL CLOCK GENERATOR
74/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.4 Functional Description Figure 41 shows the serial peripheral interface (SPI) block diagram. This interface contains three dedicated registers: - A Control Register (CR) - A Status Register (SR) - A Data Register (DR) Refer to the CR, SR and DR registers in Section 13.4.7for the bit definitions. 13.4.4.1 Master Configuration In a master configuration, the serial clock is generated on the SCK pin. Procedure - Select the SPR0 and SPR1 bits to define the serial clock baud rate (see CR register). - Select the CPOL and CPHA bits to define one of the four relationships between the data transfer and the serial clock (see Figure 44). - The SS pin must be connected to a high level signal during the complete byte transmit sequence. - The MSTR and SPE bits must be set (they remain set only if the SS pin is connected to a high level signal).
In this configuration the MOSI pin is a data output and to the MISO pin is a data input. Transmit sequence The transmit sequence begins when a byte is written the DR register. The data byte is parallel loaded into the 8-bit shift register (from the internal bus) during a write cycle and then shifted out serially to the MOSI pin most significant bit first. When data transfer is complete: - The SPIF bit is set by hardware - An interrupt is generated if the SPIE bit is set and the I bit in the CCR register is cleared. During the last clock cycle the SPIF bit is set, a copy of the data byte received in the shift register is moved to a buffer. When the DR register is read, the SPI peripheral returns this buffered value. Clearing the SPIF bit is performed by the following software sequence: 1. An access to the SR register while the SPIF bit is set 2. A read to the DR register. Note: While the SPIF bit is set, all writes to the DR register are inhibited until the SR register is read.
75/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.4.2 Slave Configuration In slave configuration, the serial clock is received on the SCK pin from the master device. The value of the SPR0 and SPR1 bits is not used for the data transfer. Procedure - For correct data transfer, the slave device must be in the same timing mode as the master device (CPOL and CPHA bits). See Figure 44. - The SS pin must be connected to a low level signal during the complete byte transmit sequence. - Clear the MSTR bit and set the SPE bit to assign the pins to alternate function. In this configuration the MOSI pin is a data input and the MISO pin is a data output. Transmit Sequence The data byte is parallel loaded into the 8-bit shift register (from the internal bus) during a write cycle and then shifted out serially to the MISO pin most significant bit first. The transmit sequence begins when the slave device receives the clock signal and the most significant bit of the data on its MOSI pin.
When data transfer is complete: - The SPIF bit is set by hardware - An interrupt is generated if SPIE bit is set and I bit in CCR register is cleared. During the last clock cycle the SPIF bit is set, a copy of the data byte received in the shift register is moved to a buffer. When the DR register is read, the SPI peripheral returns this buffered value. Clearing the SPIF bit is performed by the following software sequence: 1. An access to the SR register while the SPIF bit is set. 2.A read to the DR register. Notes: While the SPIF bit is set, all writes to the DR register are inhibited until the SR register is read. The SPIF bit can be cleared during a second transmission; however, it must be cleared before the second SPIF bit in order to prevent an overrun condition (see Section 13.4.4.6). Depending on the CPHA bit, the SS pin has to be set to write to the DR register between each data byte transfer to avoid a write collision (see Section 13.4.4.4).
76/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.4.3 Data Transfer Format During an SPI transfer, data is simultaneously transmitted (shifted out serially) and received (shifted in serially). The serial clock is used to synchronize the data transfer during a sequence of eight clock pulses. The SS pin allows individual selection of a slave device; the other slave devices that are not selected do not interfere with the SPI transfer. Clock Phase and Clock Polarity Four possible timing relationships may be chosen by software, using the CPOL and CPHA bits. The CPOL (clock polarity) bit controls the steady state value of the clock when no data is being transferred. This bit affects both master and slave modes. The combination between the CPOL and CPHA (clock phase) bits selects the data capture clock edge. Figure 44, shows an SPI transfer with the four combinations of the CPHA and CPOL bits. The diagram may be interpreted as a master or slave timing diagram where the SCK pin, the MISO pin, the MOSI pin are directly connected between the master and the slave device. The SS pin is the slave device select input and can be driven by the master device.
The master device applies data to its MOSI pinclock edge before the capture clock edge. CPHA bit is set The second edge on the SCK pin (falling edge if the CPOL bit is reset, rising edge if the CPOL bit is set) is the MSBit capture strobe. Data is latched on the occurrence of the second clock transition. No write collision should occur even if the SS pin stays low during a transfer of several bytes (see Figure 43). CPHA bit is reset The first edge on the SCK pin (falling edge if CPOL bit is set, rising edge if CPOL bit is reset) is the MSBit capture strobe. Data is latched on the occurrence of the first clock transition. The SS pin must be toggled high and low between each byte transmitted (see Figure 43). To protect the transmission from a write collision a low value on the SS pin of a slave device freezes the data in its DR register and does not allow it to be altered. Therefore the SS pin must be high to write a new data byte in the DR without producing a write collision.
Figure 43. CPHA / SS Timing Diagram
MOSI/MISO Master SS Slave SS (CPHA=0) Slave SS (CPHA=1)
Byte 1
Byte 2
Byte 3
VR02131A
77/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) Figure 44. Data Clock Timing Diagram
CPHA =1
SCLK (with CPOL = 1) SCLK (with CPOL = 0)
MISO (from master) MOSI (from slave) SS (to slave)
CAPTURE STROBE
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
CPHA =0
CPOL = 1
CPOL = 0
MISO (from master) MOSI (from slave) SS (to slave)
CAPTURE STROBE
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
MSBit
Bit 6
Bit 5
Bit 4
Bit3
Bit 2
Bit 1
LSBit
Note: This figure should not be used as a replacement for parametric information. Refer to the Electrical Characteristics chapter.
VR02131B
78/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.4.4 Write Collision Error A write collision occurs when the software tries to write to the DR register while a data transfer is taking place with an external device. When this happens, the transfer continues uninterrupted; and the software write will be unsuccessful. Write collisions can occur both in master and slave mode. Note: A "read collision" will never occur since the received data byte is placed in a buffer in which access is always synchronous with the MCU operation. In Slave mode When the CPHA bit is set: The slave device will receive a clock (SCK) edge prior to the latch of the first data transfer. This first clock edge will freeze the data in the slave device DR register and output the MSBit on to the external MISO pin of the slave device. The SS pin low state enables the slave device but the output of the MSBit onto the MISO pin does not take place until the first data transfer clock edge.
When the CPHA bit is reset: Data is latched on the occurrence of the first clock transition. The slave device does not have any way of knowing when that transition will occur; therefore, the slave device collision occurs when software attempts to write the DR register after its SS pin has been pulled low. For this reason, the SS pin must be high, between each data byte transfer, to allow the CPU to write in the DR register without generating a write collision. In Master mode Collision in the master device is defined as a write of the DR register while the internal serial clock (SCK) is in the process of transfer. The SS pin signal must be always high on the master device. WCOL bit The WCOL bit in the SR register is set if a write collision occurs. No SPI interrupt is generated when the WCOL bit is set (the WCOL bit is a status flag only). Clearing the WCOL bit is done through a software sequence (see Figure 45).
Figure 45. Clearing the WCOL bit (Write Collision Flag) Software Sequence Clearing sequence after SPIF = 1 (end of a data byte transfer) 1st Step Read SR OR
THEN
Read SR
THEN
2nd Step
Read DR
SPIF =0 WCOL=0
Write DR
SPIF =0 WCOL=0 if no transfer has started WCOL=1 if a transfer has started
before the 2nd step
Clearing sequence before SPIF = 1 (during a data byte transfer) 1st Step Read SR
THEN
2nd Step
Read DR
WCOL=0
Note: Writing to the DR register instead of reading in it does not reset the WCOL bit.
79/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.4.5 Master Mode Fault Master mode fault occurs when the master device has its SS pin pulled low, then the MODF bit is set. Master mode fault affects the SPI peripheral in the following ways: - The MODF bit is set and an SPI interrupt is generated if the SPIE bit is set. - The SPE bit is reset. This blocks all output from the device and disables the SPI peripheral. - The MSTR bit is reset, thus forcing the device into slave mode. Clearing the MODF bit is done through a software sequence: 1. A read or write access to the SR register while the MODF bit is set. 2. A write to the CR register. Notes: To avoid any multiple slave conflicts in the case of a system comprising several MCUs, the SS pin must be pulled high during the clearing sequence of the MODF bit. The SPE and MSTR bits
may be restored to their original state during or after this clearing sequence. Hardware does not allow the user to set the SPE and MSTR bits while the MODF bit is set except in the MODF bit clearing sequence. In a slave device the MODF bit can not be set, but in a multi master configuration the device can be in slave mode with this MODF bit set. The MODF bit indicates that there might have been a multimaster conflict for system control and allows a proper exit from system operation to a reset or default system state using an interrupt routine. 13.4.4.6 Overrun Condition An overrun condition occurs when the master device has sent several data bytes and the slave device has not cleared the SPIF bit issuing from the previous data byte transmitted. In this case, the receiver buffer contains the byte sent after the SPIF bit was last cleared. A read to the DR register returns this byte. All other bytes are lost. This condition is not detected by the SPI peripheral.
80/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.4.7 Single Master and Multimaster Configurations There are two types of SPI systems: For more security, the slave device may respond to the master with the received data byte. Then the - Single Master System master will receive the previous byte back from the - Multimaster System slave device if all MISO and MOSI pins are connected and the slave has not written its DR register. Single Master System Other transmission security methods can use A typical single master system may be configured, ports for handshake lines or data bytes with comusing an MCU as the master and four MCUs as mand fields. slaves (see Figure 46). Multimaster System The master device selects the individual slave deA multimaster system may also be configured by vices by using four pins of a parallel port to control the user. Transfer of master control could be imthe four SS pins of the slave devices. plemented using a handshake method through the The SS pins are pulled high during reset since the I/O ports or by an exchange of code messages master device ports will be forced to be inputs at through the serial peripheral interface system. that time, thus disabling the slave devices. The multi-master system is principally handled by the MSTR bit in the CR register and the MODF bit Note: To prevent a bus conflict on the MISO line in the SR register. the master allows only one active slave device during a transmission. Figure 46. Single Master Configuration
SS SCK Slave MCU MOSI MISO SCK Slave MCU
SS SCK Slave MCU
SS SCK Slave MCU
SS
MOSI MISO
MOSI MISO
MOSI MISO
MOSI MISO SCK Master MCU 5V SS Ports
81/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.5 Low Power Modes
Mode WAIT HALT Description No effect on SPI. SPI interrupt events cause the device to exit from Wait mode. SPI registers are frozen. In Halt mode, the SPI is inactive. SPI operation resumes when the MCU is woken up by an interrupt with "exit from Halt mode" capability.
13.4.6 Interrupts
Interrupt Event SPI End of Transfer Event Master Mode Fault Event Event Flag SPIF MODF Enable Control Bit SPIE Exit from Wait Yes Yes Exit from Halt No No
Note: The SPI interrupt events are connected to the same interrupt vector (see INTERRUPTS chapter). They generate an interrupt if the corresponding Enable Control Bit is set and the interrupt mask in
the CC register is reset (RIM instruction).
82/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) 13.4.7 Register Description CONTROL REGISTER (CR) Read/Write Reset Value: 0000xxxx (0xh)
7 0
SPIE SPE SPR2 MSTR CPOL CPHA SPR1 SPR0
Bit 3 = CPOL Clock polarity. This bit is set and cleared by software. This bit determines the steady state of the serial Clock. The CPOL bit affects both the master and slave modes. 0: The steady state is a low value at the SCK pin. 1: The steady state is a high value at the SCK pin. Bit 2 = CPHA Clock phase. This bit is set and cleared by software. 0: The first clock transition is the first data capture edge. 1: The second clock transition is the first capture edge. Bit 1:0 = SPR[1:0] Serial peripheral rate. These bits are set and cleared by software.Used with the SPR2 bit, they select one of six baud rates to be used as the serial clock when the device is a master. These 2 bits have no effect in slave mode. Table 17. Serial Peripheral Baud Rate
Bit 7 = SPIE Serial peripheral interrupt enable. This bit is set and cleared by software. 0: Interrupt is inhibited 1: An SPI interrupt is generated whenever SPIF=1 or MODF=1 in the SR register Bit 6 = SPE Serial peripheral output enable. This bit is set and cleared by software. It is also cleared by hardware when, in master mode, SS=0 (see Section 13.4.4.5 "Master Mode Fault" on page 80). 0: I/O port connected to pins 1: SPI alternate functions connected to pins The SPE bit is cleared by reset, so the SPI peripheral is not initially connected to the external pins. Bit 5 = SPR2 Divider Enable. this bit is set and cleared by software and it is cleared by reset. It is used with the SPR[1:0] bits to set the baud rate. Refer to Table 17. 0: Divider by 2 enabled 1: Divider by 2 disabled Bit 4 = MSTR Master. This bit is set and cleared by software. It is also cleared by hardware when, in master mode, SS=0 (see Section 13.4.4.5 "Master Mode Fault" on page 80). 0: Slave mode is selected 1: Master mode is selected, the function of the SCK pin changes from an input to an output and the functions of the MISO and MOSI pins are reversed.
Serial Clock fCPU/4 fCPU/8 fCPU/16 fCPU/32 fCPU/64 fCPU/128
SPR2 1 0 0 1 0 0
SPR1 0 0 0 1 1 1
SPR0 0 0 1 0 0 1
83/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) STATUS REGISTER (SR) Read Only Reset Value: 0000 0000 (00h)
7 SPIF WCOL MODF 0 -
DATA I/O REGISTER (DR) Read/Write Reset Value: Undefined
7 D7 D6 D5 D4 D3 D2 D1 0 D0
Bit 7 = SPIF Serial Peripheral data transfer flag. This bit is set by hardware when a transfer has been completed. An interrupt is generated if SPIE=1 in the CR register. It is cleared by a software sequence (an access to the SR register followed by a read or write to the DR register). 0: Data transfer is in progress or has been approved by a clearing sequence. 1: Data transfer between the device and an external device has been completed. Note: While the SPIF bit is set, all writes to the DR register are inhibited. Bit 6 = WCOL Write Collision status. This bit is set by hardware when a write to the DR register is done during a transmit sequence. It is cleared by a software sequence (see Figure 45). 0: No write collision occurred 1: A write collision has been detected Bit 5 = Unused. Bit 4 = MODF Mode Fault flag. This bit is set by hardware when the SS pin is pulled low in master mode (see Section 13.4.4.5 "Master Mode Fault" on page 80). An SPI interrupt can be generated if SPIE=1 in the CR register. This bit is cleared by a software sequence (An access to the SR register while MODF=1 followed by a write to the CR register). 0: No master mode fault detected 1: A fault in master mode has been detected Bits 3:0 = Unused.
The DR register is used to transmit and receive data on the serial bus. In the master device only a write to this register will initiate transmission/reception of another byte. Notes: During the last clock cycle the SPIF bit is set, a copy of the received data byte in the shift register is moved to a buffer. When the user reads the serial peripheral data I/O register, the buffer is actually being read. Warning: A write to the DR register places data directly into the shift register for transmission. A read to the DR register returns the value located in the buffer and not the contents of the shift register (See Figure 42).
84/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL PERIPHERAL INTERFACE (Cont'd) Table 18. SPI Register Map and Reset Values
Address (Hex.) 0021h 0022h 0023h Register Label SPIDR Reset Value SPICR Reset Value SPISR Reset Value 7 MSB x SPIE 0 SPIF 0 6 5 4 3 2 1 0 LSB x SPR0 x 0
x SPE 0 WCOL 0
x SPR2 0 0
x MSTR 0 MODF 0
x CPOL x 0
x CPHA x 0
x SPR1 x 0
85/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13.5 SERIAL COMMUNICATIONS INTERFACE (SCI) 13.5.1 Introduction The Serial Communications Interface (SCI) offers a flexible means of full-duplex data exchange with external equipment requiring an industry standard NRZ asynchronous serial data format. The SCI offers a very wide range of baud rates using two baud rate generator systems. 13.5.2 Main Features Full duplex, asynchronous communications NRZ standard format (Mark/Space) Dual baud rate generator systems Independently programmable transmit and receive baud rates up to 250K baud using conventional baud rate generator and up to 500K baud using the extended baud rate generator. Programmable data word length (8 or 9 bits) Receive buffer full, Transmit buffer empty and End of Transmission flags Two receiver wake-up modes: - Address bit (MSB) - Idle line Muting function for multiprocessor configurations LIN compatible (if MCU clock frequency tolerance 2%) Separate enable bits for Transmitter and Receiver Three error detection flags: - Overrun error - Noise error - Frame error Five interrupt sources with flags: - Transmit data register empty - Transmission complete - Receive data register full - Idle line received - Overrun error detected 13.5.3 General Description The interface is externally connected to another device by two pins (see Figure 48): - TDO: Transmit Data Output. When the transmitter is disabled, the output pin returns to its I/O port configuration. When the transmitter is enabled and nothing is to be transmitted, the TDO pin is at high level. - RDI: Receive Data Input is the serial data input. Oversampling techniques are used for data recovery by discriminating between valid incoming data and noise. Through this pins, serial data is transmitted and received as frames comprising: - An Idle Line prior to transmission or reception - A start bit - A data word (8 or 9 bits) least significant bit first - A Stop bit indicating that the frame is complete. This interface uses two types of baud rate generator: - A conventional type for commonly-used baud rates, - An extended type with a prescaler offering a very wide range of baud rates even with non-standard oscillator frequencies. 13.5.4 LIN Protocol support For LIN applications where resynchronization is not required (application clock tolerance less than or equal to 2%) the LIN protocol can be efficiently implemented with this standard SCI.
86/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) Figure 47. SCI Block Diagram
Write
Read
(DATA REGISTER) DR
Transmit Data Register (TDR) TDO Transmit Shift Register RDI
Received Data Register (RDR)
Received Shift Register
CR1
R8 T8 M
WAKE
-
-
-
TRANSMIT CONTROL
WAKE UP UNIT
RECEIVER CONTROL
RECEIVER CLOCK
CR2
TIE TCIE RIE ILIE TE RE RWU SBK TDRE TC RDRF IDLE OR NF FE
SR
-
SCI INTERRUPT CONTROL TRANSMITTER CLOCK TRANSMITTER RATE CONTROL
fCPU
/16
/2
/PR BRR
SCP1 SCP0 SCT2 SCT1 SCT0 SCR2 SCR1SCR0
RECEIVER RATE CONTROL CONVENTIONAL BAUD RATE GENERATOR
87/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) 13.5.5 Functional Description The block diagram of the Serial Control Interface, is shown in Figure 47. It contains six dedicated registers: - 2 control registers (CR1 and CR2) - A status register (SR) - A baud rate register (BRR) - An extended prescaler receiver register (ERPR) - An extended prescaler transmitter register (ETPR) Refer to the register descriptions in Section 13.5.8 for the definitions of each bit.
13.5.5.1 Serial Data Format Word length may be selected as being either 8 or 9 bits by programming the M bit in the CR1 register (see Figure 47). The TDO pin is in low state during the start bit. The TDO pin is in high state during the stop bit. An Idle character is interpreted as an entire frame of "1"s followed by the start bit of the next frame which contains data. A Break character is interpreted on receiving `0's for some multiple of the frame period. At the end of the last break frame the transmitter inserts an extra `1' bit to acknowledge the start bit. Transmission and reception are driven by their own baud rate generator.
Figure 48. Word length programming 9-bit Word length (M bit is set) Data Frame
Start Bit Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Possible Parity Bit Bit8
Next Data Frame
Next Stop Start Bit Bit Start Bit
Idle Frame
Break Frame
Extra `1'
Start Bit
8-bit Word length (M bit is reset) Data Frame
Start Bit Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6
Possible Parity Bit Bit7 Stop Bit
Next Data Frame
Next Start Bit Start Bit Extra Start Bit `1'
Idle Frame Break Frame
88/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) 13.5.5.2 Transmitter The transmitter can send data words of either 8 or 9 bits depending on the M bit status. When the M bit is set, word length is 9 bits and the 9th bit (the MSB) has to be stored in the T8 bit in the CR1 register. Character Transmission During an SCI transmission, data shifts out least significant bit first on the TDO pin. In this mode, the DR register consists of a buffer (TDR) between the internal bus and the transmit shift register (see Figure 47). Procedure - Select the M bit to define the word length. - Select the desired baud rate using the BRR and the ETPR registers. - Set the TE bit to assign the TDO pin to the alternate function and to send an idle frame as first transmission. - Access the SR register and write the data to send in the DR register (this sequence clears the TDRE bit). Repeat this sequence for each data to be transmitted. Clearing the TDRE bit is always performed by the following software sequence: 1. An access to the SR register 2. A write to the DR register The TDRE bit is set by hardware and it indicates: - The TDR register is empty. - The data transfer is beginning. - The next data can be written in the DR register without overwriting the previous data. This flag generates an interrupt if the TIE bit is set and the I bit is cleared in the CCR register. When a transmission is taking place, a write instruction to the DR register stores the data in the TDR register and which is copied in the shift register at the end of the current transmission. When no transmission is taking place, a write instruction to the DR register places the data directly in the shift register, the data transmission starts, and the TDRE bit is immediately set.
When a frame transmission is complete (after the stop bit or after the break frame) the TC bit is set and an interrupt is generated if the TCIE is set and the I bit is cleared in the CCR register. Clearing the TC bit is performed by the following software sequence: 1. An access to the SR register 2. A write to the DR register Note: The TDRE and TC bits are cleared by the same software sequence. Break Characters Setting the SBK bit loads the shift register with a break character. The break frame length depends on the M bit (see Figure 48). As long as the SBK bit is set, the SCI send break frames to the TDO pin. After clearing this bit by software the SCI insert a logic 1 bit at the end of the last break frame to guarantee the recognition of the start bit of the next frame. Idle Characters Setting the TE bit drives the SCI to send an idle frame before the first data frame. Clearing and then setting the TE bit during a transmission sends an idle frame after the current word. Note: Resetting and setting the TE bit causes the data in the TDR register to be lost. Therefore the best time to toggle the TE bit is when the TDRE bit is set i.e. before writing the next byte in the DR.
89/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) 13.5.5.3 Receiver The SCI can receive data words of either 8 or 9 bits. When the M bit is set, word length is 9 bits and the MSB is stored in the R8 bit in the CR1 register. Character reception During a SCI reception, data shifts in least significant bit first through the RDI pin. In this mode, DR register consists in a buffer (RDR) between the internal bus and the received shift register (see Figure 47). Procedure - Select the M bit to define the word length. - Select the desired baud rate using the BRR and the ERPR registers. - Set the RE bit, this enables the receiver which begins searching for a start bit. When a character is received: - The RDRF bit is set. It indicates that the content of the shift register is transferred to the RDR. - An interrupt is generated if the RIE bit is set and the I bit is cleared in the CCR register. - The error flags can be set if a frame error, noise or an overrun error has been detected during reception. Clearing the RDRF bit is performed by the following software sequence done by: 1. An access to the SR register 2. A read to the DR register. The RDRF bit must be cleared before the end of the reception of the next character to avoid an overrun error. Break Character When a break character is received, the SCI handles it as a framing error. Idle Character When an idle frame is detected, there is the same procedure as a data received character plus an interrupt if the ILIE bit is set and the I bit is cleared in the CCR register.
Overrun Error An overrun error occurs when a character is received when RDRF has not been reset. Data can not be transferred from the shift register to the TDR register as long as the RDRF bit is not cleared. When an overrun error occurs: - The OR bit is set. - The RDR content will not be lost. - The shift register will be overwritten. - An interrupt is generated if the RIE bit is set and the I bit is cleared in the CCR register. The OR bit is reset by an access to the SR register followed by a DR register read operation. Noise Error Oversampling techniques are used for data recovery by discriminating between valid incoming data and noise. When noise is detected in a frame: - The NF is set at the rising edge of the RDRF bit. - Data is transferred from the Shift register to the DR register. - No interrupt is generated. However this bit rises at the same time as the RDRF bit which itself generates an interrupt. The NF bit is reset by a SR register read operation followed by a DR register read operation. Framing Error A framing error is detected when: - The stop bit is not recognized on reception at the expected time, following either a desynchronization or excessive noise. - A break is received. When the framing error is detected: - the FE bit is set by hardware - Data is transferred from the Shift register to the DR register. - No interrupt is generated. However this bit rises at the same time as the RDRF bit which itself generates an interrupt. The FE bit is reset by a SR register read operation followed by a DR register read operation.
90/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) Figure 49. SCI Baud Rate and Extended Prescaler Block Diagram
EXTENDED PRESCALER TRANSMITTER RATE CONTROL
ETPR
EXTENDED TRANSMITTER PRESCALER REGISTER
ERPR
EXTENDED RECEIVER PRESCALER REGISTER
EXTENDED PRESCALER RECEIVER RATE CONTROL EXTENDED PRESCALER
fCPU
TRANSMITTER RATE CONTROL
TRANSMITTER CLOCK
/16
/2
/PR
BRR
SCP1 SCP0 SCT2 SCT1 SCT0 SCR2 SCR1SCR0 RECEIVER CLOCK
RECEIVER RATE CONTROL
CONVENTIONAL BAUD RATE GENERATOR
91/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) 13.5.5.4 Conventional Baud Rate Generation than zero. The baud rates are calculated as follows: The baud rate for the receiver and transmitter (Rx and Tx) are set independently and calculated as fCPU fCPU follows: Rx = Tx = fCPU fCPU 16*ERPR 16*ETPR Rx = Tx = (32*PR)*RR (32*PR)*TR with: with: ETPR = 1,..,255 (see ETPR register) PR = 1, 3, 4 or 13 (see SCP0 and SCP1 bits) ERPR = 1,.. 255 (see ERPR register) TR = 1, 2, 4, 8, 16, 32, 64,128 13.5.5.6 Receiver Muting and Wake-up Feature (see SCT0, SCT1 and SCT2 bits) In multiprocessor configurations it is often desirable that only the intended message recipient RR = 1, 2, 4, 8, 16, 32, 64,128 should actively receive the full message contents, (see SCR0,SCR1 and SCR2 bits) thus reducing redundant SCI service overhead for All this bits are in the BRR register. all non addressed receivers. Example: If fCPU is 8 MHz (normal mode) and if The non addressed devices may be placed in PR = 13 and TR = RR = 1, the transmit and resleep mode by means of the muting function. ceive baud rates are 19200 baud. Setting the RWU bit by software puts the SCI in Caution: The baud rate register (SCIBRR) MUST sleep mode: NOT be written to (changed or refreshed) while the All the reception status bits can not be set. transmitter or the receiver is enabled. All the receive interrupt are inhibited. 13.5.5.5 Extended Baud Rate Generation A muted receiver may be awakened by one of the The extended prescaler option gives a very fine following two ways: tuning on the baud rate, using a 255 value prescal- by Idle Line detection if the WAKE bit is reset, er, whereas the conventional Baud Rate Generator retains industry standard software compatibili- by Address Mark detection if the WAKE bit is set. ty. Receiver wakes-up by Idle Line detection when The extended baud rate generator block diagram the Receive line has recognized an Idle Frame. is described in the Figure 49. Then the RWU bit is reset by hardware but the IDLE bit is not set. The output clock rate sent to the transmitter or to the receiver will be the output from the 16 divider Receiver wakes-up by Address Mark detection divided by a factor ranging from 1 to 255 set in the when it received a "1" as the most significant bit of ERPR or the ETPR register. a word, thus indicating that the message is an address. The reception of this particular word wakes Note: the extended prescaler is activated by setup the receiver, resets the RWU bit and sets the ting the ETPR or ERPR register to a value other RDRF bit, which allows the receiver to receive this word normally and to use it as an address word.
92/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) 13.5.6 Low Power Modes
Mode WAIT HALT No effect on SCI. SCI interrupts cause the device to exit from Wait mode. SCI registers are frozen. In Halt mode, the SCI stops transmitting/receiving until Halt mode is exited. Description
13.5.7 Interrupts
Interrupt Event Transmit Data Register Empty Transmission Complete Received Data Ready to be Read Overrun Error Detected Idle Line Detected Event Flag TDRE TC RDRF OR IDLE Enable Control Bit TIE TCIE RIE ILIE Exit from Wait Yes Yes Yes Yes Yes Exit from Halt No No No No No
The SCI interrupt events are connected to the same interrupt vector (see INTERRUPTS chapter).
These events generate an interrupt if the corresponding Enable Control Bit is set and the interrupt mask in the CC register is reset (RIM instruction).
93/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) 13.5.8 Register Description STATUS REGISTER (SR) Read Only Reset Value: 1100 0000 (C0h)
7 TDRE TC RDRF IDLE OR NF FE 0 -
Note: The IDLE bit will not be set again until the RDRF bit has been set itself (i.e. a new idle line occurs). This bit is not set by an idle line when the receiver wakes up from wake-up mode. Bit 3 = OR Overrun error. This bit is set by hardware when the word currently being received in the shift register is ready to be transferred into the RDR register while RDRF=1. An interrupt is generated if RIE=1 in the CR2 register. It is cleared by a software sequence (an access to the SR register followed by a read to the DR register). 0: No Overrun error 1: Overrun error is detected Note: When this bit is set RDR register content will not be lost but the shift register will be overwritten. Bit 2 = NF Noise flag. This bit is set by hardware when noise is detected on a received frame. It is cleared by a software sequence (an access to the SR register followed by a read to the DR register). 0: No noise is detected 1: Noise is detected Note: This bit does not generate interrupt as it appears at the same time as the RDRF bit which itself generates an interrupt. Bit 1 = FE Framing error. This bit is set by hardware when a desynchronization, excessive noise or a break character is detected. It is cleared by a software sequence (an access to the SR register followed by a read to the DR register). 0: No Framing error is detected 1: Framing error or break character is detected Note: This bit does not generate interrupt as it appears at the same time as the RDRF bit which itself generates an interrupt. If the word currently being transferred causes both frame error and overrun error, it will be transferred and only the OR bit will be set. Bit 0 = Unused.
Bit 7 = TDRE Transmit data register empty. This bit is set by hardware when the content of the TDR register has been transferred into the shift register. An interrupt is generated if the TIE =1 in the CR2 register. It is cleared by a software sequence (an access to the SR register followed by a write to the DR register). 0: Data is not transferred to the shift register 1: Data is transferred to the shift register Note: data will not be transferred to the shift register as long as the TDRE bit is not reset. Bit 6 = TC Transmission complete. This bit is set by hardware when transmission of a frame containing Data, a Preamble or a Break is complete. An interrupt is generated if TCIE=1 in the CR2 register. It is cleared by a software sequence (an access to the SR register followed by a write to the DR register). 0: Transmission is not complete 1: Transmission is complete Bit 5 = RDRF Received data ready flag. This bit is set by hardware when the content of the RDR register has been transferred into the DR register. An interrupt is generated if RIE=1 in the CR2 register. It is cleared by a software sequence (an access to the SR register followed by a read to the DR register). 0: Data is not received 1: Received data is ready to be read Bit 4 = IDLE Idle line detect. This bit is set by hardware when an Idle Line is detected. An interrupt is generated if the ILIE=1 in the CR2 register. It is cleared by a software sequence (an access to the SR register followed by a read to the DR register). 0: No Idle Line is detected 1: Idle Line is detected
94/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) CONTROL REGISTER 1 (CR1) 1: An SCI interrupt is generated whenever TC=1 in the SR register Read/Write Reset Value: Undefined Bit 5 = RIE Receiver interrupt enable. This bit is set and cleared by software. 7 0 0: interrupt is inhibited 1: An SCI interrupt is generated whenever OR=1 R8 T8 M WAKE or RDRF=1 in the SR register Bit 7 = R8 Receive data bit 8. This bit is used to store the 9th bit of the received word when M=1. Bit 6 = T8 Transmit data bit 8. This bit is used to store the 9th bit of the transmitted word when M=1. Bit 4 = M Word length. This bit determines the word length. It is set or cleared by software. 0: 1 Start bit, 8 Data bits, 1 Stop bit 1: 1 Start bit, 9 Data bits, 1 Stop bit Bit 3 = WAKE Wake-Up method. This bit determines the SCI Wake-Up method, it is set or cleared by software. 0: Idle Line 1: Address Mark CONTROL REGISTER 2 (CR2) Read/Write Reset Value: 0000 0000 (00 h)
7
TIE TCIE RIE ILIE TE RE RWU
Bit 4 = ILIE Idle line interrupt enable. This bit is set and cleared by software. 0: interrupt is inhibited 1: An SCI interrupt is generated whenever IDLE=1 in the SR register. Bit 3 = TE Transmitter enable. This bit enables the transmitter and assigns the TDO pin to the alternate function. It is set and cleared by software. 0: Transmitter is disabled, the TDO pin is back to the I/O port configuration. 1: Transmitter is enabled Note: during transmission, a "0" pulse on the TE bit ("0" followed by "1") sends a preamble after the current word. Bit 2 = RE Receiver enable. This bit enables the receiver. It is set and cleared by software. 0: Receiver is disabled. 1: Receiver is enabled and begins searching for a start bit. Bit 1 = RWU Receiver wake-up. This bit determines if the SCI is in mute mode or not. It is set and cleared by software and can be cleared by hardware when a wake-up sequence is recognized. 0: Receiver in active mode 1: Receiver in mute mode Bit 0 = SBK Send break. This bit set is used to send break characters. It is set and cleared by software. 0: No break character is transmitted 1: Break characters are transmitted Note: If the SBK bit is set to "1" and then to "0", the transmitter will send a BREAK word at the end of the current word.
0 SBK
Bit 7 = TIE Transmitter interrupt enable. This bit is set and cleared by software. 0: interrupt is inhibited 1: An SCI interrupt is generated whenever TDRE=1 in the SR register. Bit 6 = TCIE Transmission complete interrupt enable This bit is set and cleared by software. 0: interrupt is inhibited
95/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) DATA REGISTER (DR) Read/Write Reset Value: Undefined Contains the Received or Transmitted data character, depending on whether it is read from or written to.
7 DR7 DR6 DR5 DR4 DR3 DR2 DR1 0 DR0
Bit 5:3 = SCT[2:0] SCI Transmitter rate divisor These 3 bits, in conjunction with the SCP1 and SCP0 bits, define the total division applied to the bus clock to yield the transmit rate clock in conventional Baud Rate Generator mode.
TR dividing factor 1 2 4 8 16 32 64 128 SCT2 0 0 0 0 1 1 1 1 SCT1 0 0 1 1 0 0 1 1 SCT0 0 1 0 1 0 1 0 1
The Data register performs a double function (read and write) since it is composed of two registers, one for transmission (TDR) and one for reception (RDR). The TDR register provides the parallel interface between the internal bus and the output shift register (see Figure 47). The RDR register provides the parallel interface between the input shift register and the internal bus (see Figure 47). BAUD RATE REGISTER (BRR) Read/Write Reset Value: 00 xx xxxx (XXh)
7 0
Note: this TR factor is used only when the ETPR fine tuning factor is equal to 00h; otherwise, TR is replaced by the ETPR dividing factor. Bit 2:0 = SCR[2:0] SCI Receiver rate divisor. These 3 bits, in conjunction with the SCP1 and SCP0 bits define the total division applied to the bus clock to yield the receive rate clock in conventional Baud Rate Generator mode.
RR dividing factor SCR2 0 0 0 0 1 1 1 1 SCR1 0 0 1 1 0 0 1 1 SCR0 0 1 0 1 0 1 0 1 1 2 4 8 16 32 64 128
SCP1 SCP0 SCT2 SCT1 SCT0 SCR2 SCR1 SCR0
Bit 7:6= SCP[1:0] First SCI Prescaler These 2 prescaling bits allow several standard clock division ranges:
PR Prescaling factor 1 3 4 13 SCP1 0 0 1 1 SCP0 0 1 0 1
Note: this RR factor is used only when the ERPR fine tuning factor is equal to 00h; otherwise, RR is replaced by the ERPR dividing factor.
96/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SERIAL COMMUNICATIONS INTERFACE (Cont'd) EXTENDED RECEIVE PRESCALER DIVISION REGISTER (ERPR) Read/Write Reset Value: 0000 0000 (00 h) Allows setting of the Extended Prescaler rate division factor for the receive circuit.
7 0
EXTENDED TRANSMIT PRESCALER DIVISION REGISTER (ETPR) Read/Write Reset Value:0000 0000 (00 h) Allows setting of the External Prescaler rate division factor for the transmit circuit.
7 0
ERPR ERPR ERPR ERPR ERPR ERPR ERPR ERPR 7 6 5 4 3 2 1 0
ETPR ETPR ETPR ETPR ETPR ETPR ETPR ETPR 7 6 5 4 3 2 1 0
Bit 7:1 = ERPR[7:0] 8-bit Extended Receive Prescaler Register. The extended Baud Rate Generator is activated when a value different from 00h is stored in this register. Therefore the clock frequency issued from the 16 divider (see Figure 49) is divided by the binary factor set in the ERPR register (in the range 1 to 255). The extended baud rate generator is not used after a reset. Table 19. SCI Register Map and Reset Values
Address (Hex.) 0050h 0051h 0052h 0053h 0054h 0055h 0057h Register Label SCISR Reset Value SCIDR Reset Value SCIBRR Reset Value SCICR1 Reset Value SCICR2 Reset Value SCIPBRR Reset Value SCIPBRT Reset Value 7 TDRE 1 MSB x SOG 0 R8 x TIE 0 MSB 0 MSB 0 6 TC 1 x 0 T8 x TCIE 0 0 0 5 RDRF 0 x VPOL x 0 RIE 0 0 0
Bit 7:1 = ETPR[7:0] 8-bit Extended Transmit Prescaler Register. The extended Baud Rate Generator is activated when a value different from 00h is stored in this register. Therefore the clock frequency issued from the 16 divider (see Figure 49) is divided by the binary factor set in the ETPR register (in the range 1 to 255). The extended baud rate generator is not used after a reset.
4 IDLE 0 x 2FHDET x M x ILIE 0 0 0
3 OR 0 x HVSEL x WAKE x TE 0 0 0
2 NF 0 x VCORDIS x 0 RE 0 0 0
1 FE 0 x CLPINV x 0 RWU 0 0 0
0
0 LSB x BLKINV x 0 SBK 0 LSB 0 LSB 0
97/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
13.6 8-BIT A/D CONVERTER (ADC) 13.6.1 Introduction The on-chip Analog to Digital Converter (ADC) peripheral is a 8-bit, successive approximation converter with internal sample and hold circuitry. This peripheral has up to 16 multiplexed analog input channels (refer to device pin out description) that allow the peripheral to convert the analog voltage levels from up to 16 different sources. The result of the conversion is stored in a 8-bit Data Register. The A/D converter is controlled through a Control/Status Register. 13.6.2 Main Features 8-bit conversion Up to 16 channels with multiplexed input Linear successive approximation Data register (DR) which contains the results Conversion complete status flag On/off bit (to reduce consumption) The block diagram is shown in Figure 50. Figure 50. ADC Block Diagram
fCPU fADC
13.6.3 Functional Description 13.6.3.1 Analog Power Supply VDDA and VSSA are the high and low level reference voltage pins. In some devices (refer to device pin out description) they are internally connected to the VDD and VSS pins. Conversion accuracy may therefore be impacted by voltage drops and noise in the event of heavily loaded or badly decoupled power supply lines. See ELECTRICAL CHARACTERISTICS section for more details.
DIV 2
COCO
0
ADON
0
CH3
CH2
CH1
CH0
ADCCSR
4
AIN0
HOLD CONTROL RADC ANALOG MUX
AIN1
ANALOG TO DIGITAL CONVERTER CADC
AINx
ADCDR
D7
D6
D5
D4
D3
D2
D1
D0
98/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8-BIT A/D CONVERTER (ADC) (Cont'd) 13.6.3.2 Digital A/D Conversion Result The conversion is monotonic, meaning that the result never decreases if the analog input does not and never increases if the analog input does not. If the input voltage (VAIN) is greater than or equal to VDDA (high-level voltage reference) then the conversion result in the DR register is FFh (full scale) without overflow indication. If input voltage (VAIN) is lower than or equal to VSSA (low-level voltage reference) then the conversion result in the DR register is 00h. The A/D converter is linear and the digital result of the conversion is stored in the ADCDR register. The accuracy of the conversion is described in the parametric section. RAIN is the maximum recommended impedance for an analog input signal. If the impedance is too high, this will result in a loss of accuracy due to leakage and sampling not being completed in the allotted time. 13.6.3.3 A/D Conversion Phases The A/D conversion is based on two conversion phases as shown in Figure 51: Sample capacitor loading [duration: tLOAD] During this phase, the VAIN input voltage to be measured is loaded into the CADC sample capacitor. A/D conversion [duration: tCONV] During this phase, the A/D conversion is computed (8 successive approximations cycles) and the CADC sample capacitor is disconnected from the analog input pin to get the optimum analog to digital conversion accuracy. While the ADC is on, these two phases are continuously repeated. At the end of each conversion, the sample capacitor is kept loaded with the previous measurement load. The advantage of this behavior is that it minimizes the current consumption on the analog pin in case of single input channel measurement. 13.6.3.4 Software Procedure Refer to the control/status register (CSR) and data register (DR) in Section 13.6.6 for the bit definitions and to Figure 51 for the timings. ADC Configuration The total duration of the A/D conversion is 12 ADC clock periods (1/fADC = 2/fCPU). The analog input ports must be configured as input, no pull-up, no interrupt. Refer to the I/O PORTS chapter. Using these pins as analog inputs does not affect the ability of the port to be read as a logic input. In the CSR register: - Select the CH[3:0] bits to assign the analog channel to be converted. ADC Conversion In the CSR register: - Set the ADON bit to enable the A/D converter and to start the first conversion. From this time on, the ADC performs a continuous conversion of the selected channel. When a conversion is complete - The COCO bit is set by hardware. - No interrupt is generated. - The result is in the DR register and remains valid until the next conversion has ended. A write to the CSR register (with ADON set) aborts the current conversion, resets the COCO bit and starts a new conversion. Figure 51. ADC Conversion Timings
ADON tCONV
ADCCSR WRITE OPERATION
HOLD CONTROL
tLOAD
COCO BIT SET
13.6.4 Low Power Modes
Mode WAIT HALT Description No effect on A/D Converter A/D Converter disabled. After wake-up from Halt mode, the A/D Converter requires a stabilization time before accurate conversions can be performed.
Note: The A/D converter may be disabled by resetting the ADON bit. This feature allows reduced power consumption when no conversion is needed and between single shot conversions. 13.6.5 Interrupts None
99/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8-BIT A/D CONVERTER (ADC) (Cont'd) 13.6.6 Register Description CONTROL/STATUS REGISTER (CSR) Read / Write Reset Value: 0000 0000 (00h)
7 COCO 0 ADON 0 CH3 CH2 CH1 0 CH0
DATA REGISTER (DR) Read Only Reset Value: 0000 0000 (00h)
7 D7 D6 D5 D4 D3 D2 D1 0 D0
Bit 7 = COCO Conversion Complete This bit is set by hardware. It is cleared by software reading the result in the DR register or writing to the CSR register. 0: Conversion is not complete 1: Conversion can be read from the DR register Bit 6 = Reserved. Must always be cleared. Bit 5 = ADON A/D Converter On This bit is set and cleared by software. 0: A/D converter is switched off 1: A/D converter is switched on Bit 4 = Reserved. Must always be cleared. Bits 3:0 = CH[3:0] Channel Selection These bits are set and cleared by software. They select the analog input to convert.
Channel Pin1) AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 AIN7 AIN8 AIN9 AIN10 AIN11 AIN12 AIN13 AIN14 AIN15 CH3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 CH2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 CH1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 CH0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Bits 7:0 = D[7:0] Analog Converted Value This register contains the converted analog value in the range 00h to FFh. Note: Reading this register reset the COCO flag.
Notes: 1. The number of pins AND the channel selection varies according to the device. Refer to the device pinout.
100/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8-BIT A/D CONVERTER (ADC) (Cont'd) Table 20. ADC Register Map and Reset Values
Address (Hex.) 0070h 0071h Register Label ADCDR Reset Value ADCCSR Reset Value 7 D7 0 COCO 0 6 D6 0 0 5 D5 0 ADON 0 4 D4 0 0 3 D3 0 CH3 0 2 D2 0 CH2 0 1 D1 0 CH1 0 0 D0 0 CH0 0
101/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
14 INSTRUCTION SET
14.1 ST7 ADDRESSING MODES The ST7 Core features 17 different addressing modes which can be classified in 7 main groups:
Addressing Mode Group Example Inherent Immediate Direct Indexed Indirect Relative Bit operation nop ld A,#$55 ld A,$55 ld A,($55,X) ld A,([$55],X) jrne loop bset byte,#5
The ST7 Instruction set is designed to minimize the number of bytes required per instruction: To do Table 21. ST7 Addressing Mode Overview
Mode Inherent Immediate Short Long No Offset Short Long Short Long Short Long Relative Relative Bit Bit Bit Bit Direct Direct Direct Direct Direct Indirect Indirect Indirect Indirect Direct Indirect Direct Indirect Direct Indirect Relative Relative Indexed Indexed Indexed Indexed Indexed nop ld A,#$55 ld A,$10 ld A,$1000 ld A,(X) ld A,($10,X) ld A,($1000,X) ld A,[$10] ld A,[$10.w] ld A,([$10],X) ld A,([$10.w],X) jrne loop jrne [$10] bset $10,#7 bset [$10],#7 btjt $10,#7,skip Syntax
so, most of the addressing modes may be subdivided in two sub-modes called long and short: - Long addressing mode is more powerful because it can use the full 64 Kbyte address space, however it uses more bytes and more CPU cycles. - Short addressing mode is less powerful because it can generally only access page zero (0000h 00FFh range), but the instruction size is more compact, and faster. All memory to memory instructions use short addressing modes only (CLR, CPL, NEG, BSET, BRES, BTJT, BTJF, INC, DEC, RLC, RRC, SLL, SRL, SRA, SWAP) The ST7 Assembler optimizes the use of long and short addressing modes.
Destination/ Source
Pointer Address (Hex.)
Pointer Size (Hex.) +0 +1
Length (bytes)
00..FF 0000..FFFF 00..FF 00..1FE 0000..FFFF 00..FF 0000..FFFF 00..1FE 0000..FFFF PC-128/PC+1271) PC-128/PC+1271) 00..FF 00..FF 00..FF 00..FF 00..FF byte 00..FF byte byte 00..FF 00..FF 00..FF 00..FF byte word byte word
+1 +2 + 0 (with X register) + 1 (with Y register) +1 +2 +2 +2 +2 +2 +1 +2 +1 +2 +2 +3
btjt [$10],#7,skip 00..FF
Notes: 1. At the time the instruction is executed, the Program Counter (PC) points to the instruction following JRxx.
102/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
ST7 ADDRESSING MODES (Cont'd) 14.1.1 Inherent All Inherent instructions consist of a single byte. The opcode fully specifies all the required information for the CPU to process the operation.
Inherent Instruction NOP TRAP WFI HALT RET IRET SIM RIM SCF RCF RSP LD CLR PUSH/POP INC/DEC TNZ CPL, NEG MUL SLL, SRL, SRA, RLC, RRC SWAP Function No operation S/W Interrupt Wait For Interrupt (Low Power Mode) Halt Oscillator (Lowest Power Mode) Sub-routine Return Interrupt Sub-routine Return Set Interrupt Mask Reset Interrupt Mask Set Carry Flag Reset Carry Flag Reset Stack Pointer Load Clear Push/Pop to/from the stack Increment/Decrement Test Negative or Zero 1 or 2 Complement Byte Multiplication Shift and Rotate Operations Swap Nibbles
14.1.3 Direct In Direct instructions, the operands are referenced by their memory address. The direct addressing mode consists of two submodes: Direct (short) The address is a byte, thus requires only one byte after the opcode, but only allows 00 - FF addressing space. Direct (long) The address is a word, thus allowing 64 Kbyte addressing space, but requires 2 bytes after the opcode. 14.1.4 Indexed (No Offset, Short, Long) In this mode, the operand is referenced by its memory address, which is defined by the unsigned addition of an index register (X or Y) with an offset. The indexed addressing mode consists of three sub-modes: Indexed (No Offset) There is no offset, (no extra byte after the opcode), and allows 00 - FF addressing space. Indexed (Short) The offset is a byte, thus requires only one byte after the opcode and allows 00 - 1FE addressing space. Indexed (long) The offset is a word, thus allowing 64 Kbyte addressing space and requires 2 bytes after the opcode. 14.1.5 Indirect (Short, Long) The required data byte to do the operation is found by its memory address, located in memory (pointer). The pointer address follows the opcode. The indirect addressing mode consists of two sub-modes: Indirect (short) The pointer address is a byte, the pointer size is a byte, thus allowing 00 - FF addressing space, and requires 1 byte after the opcode. Indirect (long) The pointer address is a byte, the pointer size is a word, thus allowing 64 Kbyte addressing space, and requires 1 byte after the opcode.
14.1.2 Immediate Immediate instructions have two bytes, the first byte contains the opcode, the second byte contains the operand value.
Immediate Instruction LD CP BCP AND, OR, XOR ADC, ADD, SUB, SBC Load Compare Bit Compare Logical Operations Arithmetic Operations Function
103/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
ST7 ADDRESSING MODES (Cont'd) 14.1.6 Indirect Indexed (Short, Long) This is a combination of indirect and short indexed addressing modes. The operand is referenced by its memory address, which is defined by the unsigned addition of an index register value (X or Y) with a pointer value located in memory. The pointer address follows the opcode. The indirect indexed addressing mode consists of two sub-modes: Indirect Indexed (Short) The pointer address is a byte, the pointer size is a byte, thus allowing 00 - 1FE addressing space, and requires 1 byte after the opcode. Indirect Indexed (Long) The pointer address is a byte, the pointer size is a word, thus allowing 64 Kbyte addressing space, and requires 1 byte after the opcode. Table 22. Instructions Supporting Direct, Indexed, Indirect and Indirect Indexed Addressing Modes
Long and Short Instructions LD CP AND, OR, XOR ADC, ADD, SUB, SBC BCP Load Compare Logical Operations Arithmetic Addition/subtraction operations Bit Compare Function
14.1.7 Relative Mode (Direct, Indirect) This addressing mode is used to modify the PC register value by adding an 8-bit signed offset to it.
Available Relative Direct/ Indirect Instructions JRxx CALLR Function Conditional Jump Call Relative
The relative addressing mode consists of two submodes: Relative (Direct) The offset follows the opcode. Relative (Indirect) The offset is defined in memory, of which the address follows the opcode.
Short Instructions Only CLR INC, DEC TNZ CPL, NEG BSET, BRES BTJT, BTJF SLL, SRL, SRA, RLC, RRC SWAP CALL, JP Clear
Function Increment/Decrement Test Negative or Zero 1 or 2 Complement Bit Operations Bit Test and Jump Operations Shift and Rotate Operations Swap Nibbles Call or Jump subroutine
104/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
14.2 INSTRUCTION GROUPS The ST 7 family devices use an Instruction Set consisting of 63 instructions. The instructions may
Group Load and Transfer Stack operation Increment/Decrement Compare and Tests Logical operations Bit Operation Conditional Bit Test and Branch Arithmetic operations Shift and Rotates Unconditional Jump or Call Conditional Branch Interruption management Condition Code Flag modification LD PUSH INC CP AND BSET BTJT ADC SLL JRA JRxx TRAP SIM WFI RIM HALT SCF IRET RCF CLR POP DEC TNZ OR BRES BTJF ADD SRL JRT SUB SRA JRF SBC RLC JP MUL RRC CALL SWAP CALLR SLA NOP RET BCP XOR CPL NEG RSP
be subdivided into 13 main groups as illustrated in the following table:
Instructions
Using a prebyte The instructions are described with one to four bytes. In order to extend the number of available opcodes for an 8-bit CPU (256 opcodes), three different prebyte opcodes are defined. These prebytes modify the meaning of the instruction they precede. The whole instruction becomes: PC-2 End of previous instruction PC-1 Prebyte PC Opcode PC+1 Additional word (0 to 2) according to the number of bytes required to compute the effective address
These prebytes enable instruction in Y as well as indirect addressing modes to be implemented. They precede the opcode of the instruction in X or the instruction using direct addressing mode. The prebytes are: PDY 90 Replace an X based instruction using immediate, direct, indexed, or inherent addressing mode by a Y one. PIX 92 Replace an instruction using direct, direct bit, or direct relative addressing mode to an instruction using the corresponding indirect addressing mode. It also changes an instruction using X indexed addressing mode to an instruction using indirect X indexed addressing mode. PIY 91 Replace an instruction using X indirect indexed addressing mode by a Y one.
105/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
INSTRUCTION GROUPS (Cont'd)
Mnemo ADC ADD AND BCP BRES BSET BTJF BTJT CALL CALLR CLR CP CPL DEC HALT IRET INC JP JRA JRT JRF JRIH JRIL JRH JRNH JRM JRNM JRMI JRPL JREQ JRNE JRC JRNC JRULT JRUGE JRUGT Description Add with Carry Addition Logical And Bit compare A, Memory Bit Reset Bit Set Jump if bit is false (0) Jump if bit is true (1) Call subroutine Call subroutine relative Clear Arithmetic Compare One Complement Decrement Halt Interrupt routine return Increment Absolute Jump Jump relative always Jump relative Never jump Jump if ext. interrupt = 1 Jump if ext. interrupt = 0 Jump if H = 1 Jump if H = 0 Jump if I = 1 Jump if I = 0 Jump if N = 1 (minus) Jump if N = 0 (plus) Jump if Z = 1 (equal) Jump if Z = 0 (not equal) Jump if C = 1 Jump if C = 0 Jump if C = 1 Jump if C = 0 Jump if (C + Z = 0) H=1? H=0? I=1? I=0? N=1? N=0? Z=1? Z=0? C=1? C=0? Unsigned < Jmp if unsigned >= Unsigned > jrf * Pop CC, A, X, PC inc X jp [TBL.w] reg, M H tst(Reg - M) A = FFH-A dec Y reg, M reg reg, M reg, M 0 I N N Z Z C M 0 N N N 1 Z Z Z C 1 Function/Example A=A+M+C A=A+M A=A.M tst (A . M) bres Byte, #3 bset Byte, #3 btjf Byte, #3, Jmp1 btjt Byte, #3, Jmp1 A A A A M M M M C C Dst M M M M Src H H H I N N N N N Z Z Z Z Z C C C
106/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
INSTRUCTION GROUPS (Cont'd)
Mnemo JRULE LD MUL NEG NOP OR POP Description Jump if (C + Z = 1) Load Multiply Negate (2's compl) No Operation OR operation Pop from the Stack A=A+M pop reg pop CC PUSH RCF RET RIM RLC RRC RSP SBC SCF SIM SLA SLL SRL SRA SUB SWAP TNZ TRAP WFI XOR Push onto the Stack Reset carry flag Subroutine Return Enable Interrupts Rotate left true C Rotate right true C Reset Stack Pointer Subtract with Carry Set carry flag Disable Interrupts Shift left Arithmetic Shift left Logic Shift right Logic Shift right Arithmetic Subtraction SWAP nibbles Test for Neg & Zero S/W trap Wait for Interrupt Exclusive OR A = A XOR M A M I=0 C <= Dst <= C C => Dst => C S = Max allowed A=A-M-C C=1 I=1 C <= Dst <= 0 C <= Dst <= 0 0 => Dst => C Dst7 => Dst => C A=A-M reg, M reg, M reg, M reg, M A M 1 N N 0 N N N N 1 0 N Z Z Z Z Z Z Z Z C C C C C A M N Z C 1 reg, M reg, M 0 N N Z Z C C push Y C=0 A reg CC M M M M reg, CC 0 H I N Z C N Z Function/Example Unsigned <= dst <= src X,A = X * A neg $10 reg, M A, X, Y reg, M M, reg X, Y, A 0 N Z N Z 0 C Dst Src H I N Z C
Dst[7..4] <=> Dst[3..0] reg, M tnz lbl1 S/W interrupt
107/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15 ELECTRICAL CHARACTERISTICS
15.1 PARAMETER CONDITIONS Unless otherwise specified, all voltages are referred to VSS. 15.1.1 Minimum and Maximum values Unless otherwise specified the minimum and maximum values are guaranteed in the worst conditions of ambient temperature, supply voltage and frequencies by tests in production on 100% of the devices with an ambient temperature at TA=25C and TA=TAmax (given by the selected temperature range). Data based on characterization results, design simulation and/or technology characteristics are indicated in the table footnotes and are not tested in production. Based on characterization, the minimum and maximum values refer to sample tests and represent the mean value plus or minus three times the standard deviation (mean3). 15.1.2 Typical values Unless otherwise specified, typical data is based on TA=25C, VDD=5V (for the 4.5VVDD5.5V voltage range) and VDD=3.3V (for the 3VVDD4V voltage range). They are given only as design guidelines and are not tested. 15.1.3 Typical curves Unless otherwise specified, all typical curves are given only as design guidelines and are not tested. 15.1.4 Loading capacitor The loading conditions used for pin parameter measurement are shown in Figure 52. Figure 52. Pin loading conditions 15.1.5 Pin input voltage The input voltage measurement on a pin of the device is described in Figure 53. Figure 53. Pin input voltage
ST7 PIN
VIN
ST7 PIN
CL
108/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.2 ABSOLUTE MAXIMUM RATINGS Stresses above those listed as "absolute maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device under these condi15.2.1 Voltage Characteristics
Symbol VDD - VSS VDDA - VSSA VIN 1) & 2) |VDDx| and |VSSx| VDDX- VDDA |VSSA - VSSx| VESD(HBM) VESD(MM) Supply voltage Analog Reference Voltage Input voltage on true open drain pin Input voltage on any other pin Variations between different digital power pins Variations between digital and analog power pins Electrostatic discharge voltage (Human Body Model) Electrostatic discharge voltage (Machine Model) Ratings
tions is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.
Maximum value 6.5 6.5 VSS-0.3 to 6.5 VSS-0.3 to VDD+0.3 50 50
Unit
V
mV
see Section 15.7.2 "Absolute Electrical Sensitivity" on page 125
15.2.2 Current Characteristics
Symbol IVDD IVSS IIO Ratings Total current into VDD power lines (source) Total current out of VSS ground lines (sink)
3) 3)
Maximum value 150 150 25 50 - 25 5 5 5 5 20
5) & 6)
Unit
Output current sunk by any standard I/O and control pin Output current sunk by any high sink I/O pin Output current source by any I/Os and control pin Injected current on ISPSEL pin IINJ(PIN) 2) & 4) Injected current on RESET pin Injected current on OSC1 and OSC2 pins Injected current on any other pin IINJ(PIN) 2) Total injected current (sum of all I/O and control pins) 5)
mA
Notes: 1. Directly connecting the RESET and I/O pins to VDD or VSS could damage the device if an unintentional internal reset is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter). To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7k for RESET, 10k for I/Os). Unused I/O pins must be tied in the same way to VDD or VSS according to their reset configuration. 2. When the current limitation is not possible, the VIN absolute maximum rating must be respected, otherwise refer to IINJ(PIN) specification. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN109/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
ABSOLUTE MAXIMUM RATINGS (Cont'd) 15.2.3 Thermal Characteristics
Symbol TSTG TJ Ratings Storage temperature range Value -65 to +150 Unit C
Maximum junction temperature (see Section 17 "DEVICE CONFIGURATION AND ORDERING INFORMATION" on page 143)
110/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.3 OPERATING CONDITIONS 15.3.1 General Operating Conditions
Symbol VDD fOSC Parameter Supply voltage External clock frequency Conditions see Figure 54 and Figure 55 VDD3.5V for ROM devices VDD4.5V for Flash devices VDD3.2V Suffix A version TA Ambient temperature range Suffix B version Suffix C version -40 Min 3.2 0 1) 0 1) Max 5.5 16 8 +85 +105 +125 C Unit V MHz
Figure 54. fOSC Maximum Operating Frequency Versus VDD Supply Voltage for ROM devices 2)
fOSC [MHz] FUNCTIONALITY NOT GUARANTEED IN THIS AREA AT TA > 85C
FUNCTIONALITY GUARANTEED IN THIS AREA
16 FUNCTIONALITY NOT GUARANTEED IN THIS AREA
12
8 4 1 0 2.5 3.2 3.5 3.85 4 4.5 5 5.5
FUNCTIONALITY NOT GUARANTEED IN THIS AREA WITH RESONATOR 1)
SUPPLY VOLTAGE [V]
Figure 55. fOSC Maximum Operating Frequency Versus VDD Supply Voltage for Flash devices 2)
fOSC [MHz] FUNCTIONALITY NOT GUARANTEED IN THIS AREA AT TA > 85C
FUNCTIONALITY GUARANTEED IN THIS AREA 3)
16 FUNCTIONALITY NOT GUARANTEED IN THIS AREA 12 8 4 1 0 2.5 3.2 3.5 3.85 4 4.5 5 5.5 SUPPLY VOLTAGE [V] FUNCTIONALITY NOT GUARANTEED IN THIS AREA WITH RESONATOR 1)
Notes: 1. Guaranteed by construction. A/D operation and resonator oscillator start-up are not guaranteed below 1MHz. 2. Operating conditions with TA=-40 to +125C. 3. Flash programming tested in production at maximum TA with two different conditions: VDD=5.5V, fCPU=6MHz and VDD=3.2V, fCPU=4MHz.
111/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
OPERATING CONDITIONS (Cont'd) 15.3.2 Operating Conditions with Low Voltage Detector (LVD) Subject to general operating conditions for VDD, fOSC, and TA.
Symbol VIT+ Parameter Reset release threshold (VDD rise) Reset generation threshold (VDD fall) LVD voltage threshold hysteresis VDD rise time rate 3) Filtered glitch delay on VDD 2) Not detected by the LVD Conditions High Threshold Med. Threshold Low Threshold High Threshold Med. Threshold Low Threshold4) VIT+-VITMin 4.10 3.75 2) 3.25 2) 3.852) 3.502) 3.00 200 0.2
2)
Typ 1) 4.30 3.90 3.35 4.05 3.65 3.10 250
Max 4.50 4.05 3.55 4.30 3.95 3.35 300 50 40
Unit
V
VITVhys VtPOR tg(VDD)
mV V/ms ns
Figure 56. High LVD Threshold Versus VDD and fOSC for Flash devices 3)
fOSC [MHz] DEVICE UNDER RESET IN THIS AREA 16 12 8 0 2.5 3 3.5 VIT-3.85 FUNCTIONALITY AND RESET NOT GUARANTEED IN THIS AREA FOR TEMPERATURES HIGHER THAN 85C FUNCTIONALITY NOT GUARANTEED IN THIS AREA FUNCTIONAL AREA SUPPLY VOLTAGE [V] 4 4.5 5 5.5
Figure 57. Medium LVD Threshold Versus VDD and fOSC for Flash devices 3)
fOSC [MHz] DEVICE UNDER RESET IN THIS AREA 16 12 8 0 2.5 3 FUNCTIONALITY AND RESET NOT GUARANTEED IN THIS AREA FOR TEMPERATURES HIGHER THAN 85C FUNCTIONALITY NOT GUARANTEED IN THIS AREA FUNCTIONAL AREA SUPPLY VOLTAGE [V] 4 4.5 5 5.5
VIT-3.5V
Figure 58. Low LVD Threshold Versus VDD and fOSC for Flash devices 2)4)
fOSC [MHz] 16 12 DEVICE UNDER RESET IN THIS AREA 8 SEE NOTE 4 0 2.5 VIT-3V 3.2 SUPPLY VOLTAGE [V] 3.5 4 4.5 5 5.5 FUNCTIONALITY NOT GUARANTEED IN THIS AREA FOR TEMPERATURES HIGHER THAN 85C FUNCTIONALITY NOT GUARANTEED IN THIS AREA FUNCTIONAL AREA
Notes: 1. LVD typical data is based on TA=25C. They are given only as design guidelines and are not tested. 2. Data based on characterization results, not tested in production. 3. The VDD rise time rate condition is needed to insure a correct device power-on and LVD reset. Not tested in production. 4.If the low LVD threshold is selected, when VDD falls below 3.2V, (VDD minimum operating voltage), the device is guaranteed to continue functioning until it goes into reset state. The specified VDD min. value is necessary in the device power on phase, but during a power down phase or voltage drop the device will function below this min. level.
112/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
FUNCTIONAL OPERATING CONDITIONS (Cont'd) Figure 59. High LVD Threshold Versus VDD and fOSC for ROM devices 2)
fOSC [MHz] DEVICE UNDER RESET IN THIS AREA 16 8 0 2.5 3 3.5 VIT-3.85 FUNCTIONALITY NOT GUARANTEED IN THIS AREA FUNCTIONAL AREA SUPPLY VOLTAGE [V] 4 4.5 5 5.5
Figure 60. Medium LVD Threshold Versus VDD and fOSC for ROM devices 2)
fOSC [MHz] DEVICE UNDER RESET IN THIS AREA 16 8 0 2.5 3 FUNCTIONALITY NOT GUARANTEED IN THIS AREA FUNCTIONAL AREA SUPPLY VOLTAGE [V] 4 4.5 5 5.5
VIT-3.5V
Figure 61. Low LVD Threshold Versus VDD and fOSC for ROM devices 2)3)
fOSC [MHz] 16 DEVICE UNDER RESET IN THIS AREA 8 0 2.5 FUNCTIONALITY NOT GUARANTEED IN THIS AREA FUNCTIONAL AREA SUPPLY VOLTAGE [V] 3.5 4 4.5 5 5.5
VIT-3.00V
Notes: 1. LVD typical data is based on TA=25C. They are given only as design guidelines and are not tested. 2. The minimum VDD rise time rate is needed to insure a correct device power-on and LVD reset. Not tested in production. 3. If the low LVD threshold is selected, when VDD falls below 3.2V, (VDD minimum operating voltage), the device is guaranteed to continue functioning until it goes into reset state. The specified VDD min. value is necessary in the device power on phase, but during a power down phase or voltage drop the device will function below this min. level.
113/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.4 SUPPLY CURRENT CHARACTERISTICS The following current consumption specified for the ST7 functional operating modes over temperature range does not take into account the clock source current consumption. To get the total deSymbol IDD(Ta) Parameter Supply current variation vs. temperature
vice consumption, the two current values must be added (except for Halt mode for which the clock is stopped).
Conditions Constant VDD and fCPU Max 10 Unit %
15.4.1 Run and Slow Modes
Symbol Parameter 4.5VVDD5.5V Supply current in Run mode 3) (see Figure 62) Supply current in Slow mode 4) (see Figure 63) IDD Supply current in Run mode (see Figure 62) 3.2VVDD3.6V
3)
Conditions fOSC=2MHz, fCPU=1MHz fOSC=4MHz, fCPU=2MHz fOSC=8MHz, fCPU=4MHz fOSC=16MHz, fCPU=8MHz fOSC=2MHz, fCPU=62.5kHz fOSC=4MHz, fCPU=125kHz fOSC=8MHz, fCPU=250kHz fOSC=16MHz, fCPU=500kHz fOSC=2MHz, fCPU=1MHz fOSC=4MHz, fCPU=2MHz fOSC=8MHz, fCPU=4MHz fOSC=16MHz, fCPU=8MHz fOSC=2MHz, fCPU=62.5kHz fOSC=4MHz, fCPU=125kHz fOSC=8MHz, fCPU=250kHz fOSC=16MHz, fCPU=500kHz
Typ 1) 1.2 2.1 3.9 7.4 0.4 0.5 0.7 1.0 0.3 0.8 1.6 3.5 0.1 0.2 0.3 0.5
Max 2) 1.8 3.5 7.0 14.0 0.9 1.1 1.4 2.0 1 1.5 3 7 0.3 0.5 0.6 1.0
Unit
mA
Supply current in Slow mode 4) (see Figure 63)
Figure 62. Typical IDD in RUN vs. fCPU
IDD [mA] 8 7 6 8MHz 4MHz 2MHz 1MHz
Figure 63. Typical IDD in SLOW vs. fCPU
IDD [mA] 1.2 500kHz 250kHz 1 125kHz 62.5kHz
0.8 5 4 3 2 0.2 1 0 3.2 3.5 4 4.5 5 5.5 VDD [V] 0 3.2 3.5 4 4.5 5 5.5 VDD [V] 0.6
0.4
Notes: 1. Typical data is based on TA=25C, VDD=5V (4.5VVDD5.5V range) and VDD=3.4V (3.2VVDD3.6V range). 2. Data based on characterization results, tested in production at VDD max. and fCPU max. 3. CPU running with memory access, all I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (OSC1) driven by external square wave, CSS and LVD disabled. 4. Slow mode selected with fCPU based on fOSC divided by 32. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (OSC1) driven by external square wave, CSS and LVD disabled.
114/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SUPPLY CURRENT CHARACTERISTICS (Cont'd) 15.4.2 Wait and Slow Wait Modes
Symbol Parameter 4.5VVDD5.5V Supply current in Wait mode 3) (see Figure 64) Supply current in Slow Wait mode 4) (see Figure 65) IDD 3.2VVDD3.6V Supply current in Wait mode 3) (see Figure 64)
4)
Conditions fOSC=2MHz, fCPU=1MHz fOSC=4MHz, fCPU=2MHz fOSC=8MHz, fCPU=4MHz fOSC=16MHz, fCPU=8MHz fOSC=2MHz, fCPU=62.5kHz fOSC=4MHz, fCPU=125kHz fOSC=8MHz, fCPU=250kHz fOSC=16MHz, fCPU=500kHz fOSC=2MHz, fCPU=1MHz fOSC=4MHz, fCPU=2MHz fOSC=8MHz, fCPU=4MHz fOSC=16MHz, fCPU=8MHz fOSC=2MHz, fCPU=62.5kHz fOSC=4MHz, fCPU=125kHz fOSC=8MHz, fCPU=250kHz fOSC=16MHz, fCPU=500kHz
Typ 1) 0.35 0.7 1.3 2.5 0.05 0.1 0.2 0.5 45 150 300 500 6 40 80 120
Max 2) 0.6 1.2 2.1 4.0 0.1 0.2 0.4 1.0 100 300 600 1000 20 100 160 250
Unit
mA
A
Supply current in Slow Wait mode (see Figure 65)
Figure 64. Typical IDD in WAIT vs. fCPU
IDD [mA] 3 8MHz 4MHz 2.5 2MHz 1MHz
Figure 65. Typical IDD in SLOW WAIT vs. fCPU
IDD [mA] 0.35 0.3 0.25 500kHz 250kHz 125kHz 62.5kHz
2 0.2 1.5 0.15 1 0.1 0.5 0.05 0 3.2 3.5 4 4.5 5 5.5 3.2 3.5 4 4.5 5 5.5 VDD [V] VDD [V]
0
Notes: 1. Typical data is based on TA=25C, VDD=5V (4.5VVDD5.5V range) and VDD=3.4V (3.2VVDD3.6V range). 2. Data based on characterization results, tested in production at VDD max. and fCPU max. 3. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (OSC1) driven by external square wave, CSS and LVD disabled. 4. Slow Wait mode selected with fCPU based on fOSC divided by 32. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (OSC1) driven by external square wave, CSS and LVD disabled.
115/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
SUPPLY CURRENT CHARACTERISTICS (Cont'd) 15.4.3 Halt and Active Halt Modes
Symbol Parameter Supply current in Halt mode 2) Supply current in Active Halt mode 3) Conditions -40CTA+85C VDD=5.5V -40CTA+125C -40CTA+85C VDD=3.6V -40CTA+125C Typ 1) Max 10 150 6 100 150 Unit
IDD
<2
A
50
15.4.4 Supply and Clock Managers The previous current consumption specified for the ST7 functional operating modes over temperature range does not take into account the clock
Symbol Parameter Supply current of internal RC oscillator Supply current of external RC oscillator 5) IDD(CK)
source current consumption. To get the total device consumption, the two current values must be added (except for Halt mode).
Conditions Typ 1) 500 525 200 300 450 700 150 Halt mode 100 Max 4) 750 750 400 550 750 1000 350 150 A Unit
LP: Low power oscillator 5) & 6) MP: Medium power oscillator Supply current of resonator oscillator MS: Medium speed oscillator HS: High speed oscillator Clock security system supply current LVD supply current
IDD(LVD)
15.4.5 On-Chip Peripherals
Symbol IDD(TIM) IDD(SPI) IDD(ADC) Parameter 16-bit Timer supply current 7) SPI supply current 8) ADC supply current when converting 9) Conditions VDD=3.4V fCPU=8MHz VDD=5.0V VDD=3.4V fCPU=8MHz VDD=5.0V VDD=3.4V fADC=4MHz VDD=5.0V Typ 50 150 250 350 800 1100 Unit
A
Notes: 1. Typical data is based on TA=25C. 2. All I/O pins in input mode with a static value at VDD or VSS (no load), CSS and LVD disabled. Data based on characterization results, tested in production at VDD max. and fCPU max. 3. Data based on design simulation and/or technology characteristics, not tested in production. All I/O pins in input mode with a static value at VDD or VSS (no load); clock input (OSC1) driven by external square wave, LVD disabled. 4. Data based on characterization results, not tested in production. 5. Data based on characterization results done with the external components specified in Section 15.5.3 and Section 15.5.4, not tested in production. 6. As the oscillator is based on a current source, the consumption does not depend on the voltage. 7. Data based on a differential IDD measurement between reset configuration (timer counter running at fCPU/4) and timer counter stopped (selecting external clock capability). Data valid for one timer. 8. Data based on a differential IDD measurement between reset configuration and a permanent SPI master communication (data sent equal to 55h). 9. Data based on a differential IDD measurement between reset configuration and continuous A/D conversions.
116/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.5 CLOCK AND TIMING CHARACTERISTICS Subject to general operating conditions for VDD, fOSC, and TA. 15.5.1 General Timings
Symbol tc(INST) tv(IT) Parameter Instruction cycle time Interrupt reaction time 2) tv(IT) = tc(INST) + 10 Conditions fCPU=8MHz fCPU=8MHz Min 2 250 10 1.25 Typ 1) 3 375 Max 12 1500 22 2.75 Unit tCPU ns tCPU s
15.5.2 External Clock Source
Symbol VOSC1H VOSC1L tw(OSC1H) tw(OSC1L) tr(OSC1) tf(OSC1) IL Parameter OSC1 input pin high level voltage OSC1 input pin low level voltage OSC1 high or low time 3) OSC1 rise or fall time 3) OSCx Input leakage current VSSVINVDD see Figure 66 Conditions Min 0.7xVDD VSS 15 ns 15 1 A Typ Max VDD 0.3xVDD Unit V
Figure 66. Typical Application with an External Clock Source
90% VOSC1H 10%
VOSC1L tr(OSC1) tf(OSC1) tw(OSC1H) tw(OSC1L)
OSC2
Not connected internally fOSC
EXTERNAL CLOCK SOURCE
OSC1
IL ST72XXX
Notes: 1. Data based on typical application software. 2. Time measured between interrupt event and interrupt vector fetch. tc(INST) is the number of tCPU cycles needed to finish the current instruction execution. 3. Data based on design simulation and/or technology characteristics, not tested in production.
117/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CLOCK AND TIMING CHARACTERISTICS (Cont'd) 15.5.3 Crystal and Ceramic Resonator Oscillators The ST7 internal clock can be supplied with four different Crystal/Ceramic resonator oscillators. All the information given in this paragraph are based on characterization results with specified typical external components. In the application, the resonator and the load capacitors have to be placed as
Symbol fOSC RF CL1 CL2 Parameter Oscillator Frequency 3) Feedback resistor Recommended load capacitance versus equivalent serial resistance of the crystal or ceramic resonator (RS)
close as possible to the oscillator pins in order to minimize output distortion and start-up stabilization time. Refer to the crystal/ceramic resonator manufacturer for more details (frequency, package, accuracy...).
Conditions Min 1 >2 >4 >8 20 38 32 18 15 40 110 180 400 Max 2 4 8 16 40 56 46 26 21 100 190 360 700 Unit MHz k pF
LP: Low power oscillator MP: Medium power oscillator MS: Medium speed oscillator HS: High speed oscillator RS=200 RS=200 RS=200 RS=100 VDD=5V VIN=VSS LP oscillator MP oscillator MS oscillator HS oscillator LP oscillator MP oscillator MS oscillator HS oscillator
i2
OSC2 driving current
A
15.5.3.1 Typical Crystal Resonators
Option Byte Config. LP MP MS HS JAUCH Reference S-200-30-30/50 SS3-400-30-30/30 SS3-800-30-30/30 SS3-1600-30-30/30 Freq. Characteristic 1) CL1 CL2 tSU(osc) [pF] [pF] [ms] 2) 33 33 33 33 34 34 34 34 10~15 7~10 2.5~3 1~1.5
2MHz fOSC=[30ppm25C,30ppmTa], Typ. RS=200 4MHz fOSC=[30ppm25C,30ppmTa], Typ. RS=60 8MHz fOSC=[30ppm25C,30ppmTa], Typ. RS=25 16MHz fOSC=[30ppm25C,30ppmTa], Typ. RS=15
Figure 67. Application with a Crystal Resonator
i2 fOSC OSC1
CL1
RESONATOR CL2 OSC2
RF ST72XXX
Notes: 1. Resonator characteristics given by the crystal manufacturer. 2. tSU(OSC) is the typical oscillator start-up time measured between VDD=2.8V and the fetch of the first instruction (with a quick VDD ramp-up from 0 to 5V (<50s). 3. The oscillator selection can be optimized in terms of supply current using a high quality resonator with small RS value. Refer to crystal manufacturer for more details.
118/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CLOCK AND TIMING CHARACTERISTICS (Cont'd) 15.5.3.2 Typical Ceramic Resonators
Symbol Parameter Conditions LP 2MHz MP 4MHz MS 8MHz HS 16MHz Typ 4.2 2.1 1.1 0.7 Unit
tSU(osc)
Ceramic resonator start-up time
ms
Note: tSU(OSC) is the typical oscillator start-up time measured between VDD=2.8V and the fetch of the first instruction (with a quick VDD ramp-up from 0 to 5V (<50s).
Figure 68. Application with Ceramic Resonator
WHEN RESONATOR WITH INTEGRATED CAPACITORS
i2
fOSC OSC1 RESONATOR
CL1
RF(EXT)
CL2 OSC2
RF ST72XXX
RD
Notes: 1. Resonator characteristics given by the ceramic resonator manufacturer. 2. tSU(OSC) is the typical oscillator start-up time measured between VDD=2.8V and the fetch of the first instruction (with a quick VDD ramp-up from 0 to 5V (<50s). 3. The oscillator selection can be optimized in terms of supply current using a high quality resonator with small RS value. Refer to Table 23 and Table 24 and to the ceramic resonator manufacturer's documentation for more details.
119/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CLOCK AND TIMING CHARACTERISTICS (Cont'd) Table 23. Typical Ceramic Resonators
Option Byte Config. fOSC (MHz) 1 LP 2 2 MP 4 4 MS 8 8 10 HS 12 Resonator Part Number1) CSB1000JA CSBF1000JA CSTS0200MGA06 CSTCC2.00MGA0H6 CSTS0200MGA06 CSTCC2.00MGA0H6 CSTS0400MGA06 CSTCC4.00MGA0H6 CSTS0400MGA06 CSTCC4.00MGA0H6 CSTS0800MGA06 CSTCC8.00MGA0H6 CSTS0800MGA06 CSTCC8.00MGA0H6 CST10.0MTWA CSTCC10.0MGA CST12.0MTWA CSTCS12.0MTA CSA16.00MXZA040 162) CST16.00MXWA0C3 CSACV16.00MXA040Q CSTCV16.00MXA0H3Q 30 (15) 30 (30) 15 (15) 15 (15) 30 (15) 30 (30) 15 (15) 15 (15) 10 (47) (47) Open 0 CL1 [pF]
3
CL2 [pF]
3
RFEXT k
RD [k] 3.3
100
100
Table 24. Resonator Frequency Correlation Factor
Option Byte Config. LP Resonator1) CSB1000JA CSTS0200MGA06 CSTCC2.00MGA0H6 CSTS0200MGA06 MP CSTCC2.00MGA0H6 CSTS0400MGA06 CSTCC4.00MGA0H6 Correla- Reference tion % IC +0.03 -0.20 -0.16 -0.21 -0.19 0.02 -0.05 4069UBE MS 74HCU04 Option Byte Config. Resonator1) CSTS0400MGA06 CSTCC4.00MGA0H6 CSTS0800MGA06 CSTCC4.00MGA0H6 CSTS0800MGA06 CSTCC8.00MGA0H6 CSTS10.0MTWA CSTCC10.0MGA CST12.0MTWA CSTCS12.0MTA CSA16.00MXZA040 CSACV16.00MXA040Q Correla- Reference tion % IC -0.03 -0.05 +0.03 +0.02 +0.02 +0.01 +0.38 +0.61 +0.38 +0.42 +0.10 +0.08
74HCU04
HS
4069UBE
74HCU04
Notes: 1. Murata Ceralock 2. VDD 4.5 to 5.5V 3. Values in parentheses refer to the capacitors integrated in the resonator
120/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CLOCK CHARACTERISTICS (Cont'd) 15.5.4 RC Oscillators The ST7 internal clock can be supplied with an RC oscillator. This oscillator can be used with internal
Symbol fOSC Parameter Internal RC oscillator frequency 1) External RC oscillator frequency 2) Internal RC Oscillator Start-up Time 3) tSU(OSC)
or external components (selectable by option byte).
Conditions Min 3.60 1 2.0 1.0 6.5 0.7 3.0 10 0
5)
Typ
Max 5.10 14
Unit MHz
see Figure 70
REX CEX
REX = 47K, CEX = "0"pF 3) REX = 47K, CEX = 100pF External RC Oscillator Start-up Time REX = 10K, CEX = 6.8pF REX = 10K, CEX = 470pF Oscillator external resistor 4) see Figure 71 Oscillator external capacitor
ms
47 470
K pF
Figure 69. Typical Application with RC oscillator
ST72XXX
INTERNAL RC VDD
Current copy
EXTERNAL RC REX OSC1
VREF
+ -
fOSC
CEX
OSC2
Voltage generator
CEX discharge
Figure 70. Typical Internal RC Oscillator
fosc [MHz] 4.3 4.2 4.1 -40C +25C +85C +125C
Figure 71. Typical External RC Oscillator
fosc [MHz] 20 15 10 Rex=10KOhm Rex=15KOhm Rex=22KOhm Rex=33KOhm Rex=39KOhm Rex=47KOhm
4 3.9 3.8 3.2 VDD [V] 5.5
5 0 0 6.8 22 47 Cex [pF] 100 270 470
Notes: 1. Data based on characterization results. 2. Guaranteed frequency range with the specified CEX and REX ranges taking into account the device process variation. Data based on design simulation. 3. Data based on characterization results done with VDD nominal at 5V, not tested in production. 4. REX must have a positive temperature coefficient (ppm/C), carbon resistors should therefore not be used. 5. Important: When no external CEX is applied, the capacitance to be considered is the global parasitic capacitance which is subject to high variation (package, application...). In this case, the RC oscillator frequency tuning has to be done by trying out several resistor values.
121/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CLOCK CHARACTERISTICS (Cont'd) 15.5.5 Clock Security System (CSS)
Symbol fSFOSC fGFOSC Parameter Safe Oscillator Frequency 1) Glitch Filtered Frequency 2) Conditions TA=25C, VDD=5.0V TA=25C, VDD=3.4V Min 250 190 Typ 340 260 30 Max 550 450 Unit kHz MHz
Figure 72. Typical Safe Oscillator Frequencies
fosc [kHz] 400 350 300 -40C +25C +85C +125C
250 200 3.2 VDD [V] 5.5
Note: 1. Data based on characterization results, tested in production between 90kHz and 600kHz. 2. Filtered glitch on the fOSC signal. See functional description in Section 8.4 on page 32 for more details.
122/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.6 MEMORY CHARACTERISTICS 15.6.1 RAM and Hardware Registers
Symbol VRM Parameter Data retention mode 1) Conditions Halt mode (or RESET) Min 1.6 Typ Max Unit V
15.6.2 EEPROM Data Memory
Symbol tprog tret NRW Parameter Programming time for 1~16 bytes 3) Data retention 5) Write erase cycles 5) Conditions -40CTA+85C -40CTA+125C TA=+55C 4) TA=+25C 20 300000 Min Typ Max 20 25 Unit ms years cycles
15.6.3 Flash Program Memory
Symbol TA(prog) tprog tret NRW Parameter Programming temperature range 2) Programming time for 1~16 bytes 3) Programming time for 4 or 8Kbytes Data retention 5) Write erase cycles 5) Conditions TA=+25C TA=+25C TA=+55C 4) TA=+25C Min 0 Typ 25 8 2.1 Max 70 25 6.4 Unit C ms sec years cycles
20 100
Notes: 1. Minimum VDD supply voltage without losing data stored in RAM (in Halt mode or under RESET) or in hardware registers (only in Halt mode). Guaranteed by construction, not tested in production. 2. Data based on characterization results, tested in production at TA = 25C. 3. Up to 16 bytes can be programmed at a time for a 4 Kbytes Flash block (then up to 32 bytes at a time for an 8K device) 4. The data retention time increases when the TA decreases. 5. Data based on reliability test results and monitored in production.
123/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.7 EMC CHARACTERISTICS Susceptibility tests are performed on a sample basis during product characterization. 15.7.1 Functional EMS (Electromagnetic Susceptibility) Based on a simple running application on the product (toggling two LEDs through I/O ports), the product is stressed by two electromagnetic events until a failure occurs (indicated by the LEDs). ESD: Electrostatic Discharge (positive and negative) is applied on all pins of the device until a functional disturbance occurs. This test conforms with the IEC 1000-4-2 standard. FTB: A Burst of Fast Transient voltage (positive and negative) is applied to VDD and VSS through a 100pF capacitor, until a functional disturbance occurs. This test conforms with the IEC 1000-44 standard. A device reset allows normal operations to be resumed.
Symbol VFESD VFFTB
Parameter Voltage limits to be applied on any I/O pin to induce a functional disturbance Fast transient voltage burst limits to be applied through 100pF on VDD and VDD pins to induce a functional disturbance
Conditions VDD=5V, TA=+25C, fOSC=8MHz conforms to IEC 1000-4-2 VDD=5V, TA=+25C, fOSC=8MHz conforms to IEC 1000-4-4
Neg 1) -1 -4
Pos 1) 1
Unit
kV 4
Figure 73. EMC Recommended star network power supply connection 2)
ST72XXX 10F 0.1F
ST7 DIGITAL NOISE FILTERING
VDD
VSS
VDD
POWER SUPPLY SOURCE
VSSA
EXTERNAL NOISE FILTERING
VDDA 0.1F
Notes: 1. Data based on characterization results, not tested in production. 2. The suggested 10F and 0.1F decoupling capacitors on the power supply lines are proposed as a good price vs. EMC performance trade-off. They have to be put as close as possible to the device power supply pins. Other EMC recommendations are given in other sections (I/Os, RESET, OSCx pin characteristics).
124/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
EMC CHARACTERISTICS (Cont'd) 15.7.2 Absolute Electrical Sensitivity Based on three different tests (ESD, LU and DLU) using specific measurement methods, the product is stressed in order to determine its performance in terms of electrical sensitivity. For more details, refer to the AN1181 ST7 application note. 15.7.2.1 Electrostatic Discharge (ESD) Electrostatic Discharges (3 positive then 3 negative pulses separated by 1 second) are applied to the pins of each sample according to each pin combination. The sample size depends of the number of supply pins of the device (3 parts*(n+1) supply pin). Two models are usually simulated: Human Body Model and Machine Model. This test conforms to the JESD22-A114A/A115A standard. See Figure 74 and the following test sequences. Human Body Model Test Sequence - CL is loaded through S1 by the HV pulse generator. - S1 switches position from generator to R. - A discharge from CL through R (body resistance) to the ST7 occurs. - S2 must be closed 10 to 100ms after the pulse delivery period to ensure the ST7 is not left in charge state. S2 must be opened at least 10ms prior to the delivery of the next pulse. Absolute Maximum Ratings
Symbol VESD(HBM) VESD(MM) Ratings Electrostatic discharge voltage (Human Body Model) Electrostatic discharge voltage (Machine Model)
Machine Model Test Sequence - CL is loaded through S1 by the HV pulse generator. - S1 switches position from generator to ST7. - A discharge from CL to the ST7 occurs. - S2 must be closed 10 to 100ms after the pulse delivery period to ensure the ST7 is not left in charge state. S2 must be opened at least 10ms prior to the delivery of the next pulse. - R (machine resistance), in series with S2, ensures a slow discharge of the ST7.
Conditions TA=+25C TA=+25C
Maximum value 1) Unit 3000 V 400
Figure 74. Typical Equivalent ESD Circuits
S1 R=1500 S1 R=10k~10M
HIGH VOLTAGE PULSE GENERATOR
CL=100pF
ST7
S2
HIGH VOLTAGE PULSE GENERATOR CL=200pF
ST7
S2
HUMAN BODY MODEL
MACHINE MODEL
Notes: 1. Data based on characterization results, not tested in production.
125/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
EMC CHARACTERISTICS (Cont'd) 15.7.2.2 Static and Dynamic Latch-Up LU: 3 complementary static tests are required on 10 parts to assess the latch-up performance. A supply overvoltage (applied to each power supply pin), a current injection (applied to each input, output and configurable I/O pin) and a power supply switch sequence are performed on each sample. This test conforms to the EIA/ JESD 78 IC latch-up standard. For more details, refer to the AN1181 ST7 application note. DLU: Electrostatic Discharges (one positive then one negative test) are applied to each pin of three samples when the micro is running to assess the latch-up performance in dynamic mode. Power supplies are set to the typical values, the oscillator is connected as near as possible to the pins of the micro and the component is put in reset mode. This test conforms to the IEC1000-4-2 and SAEJ1752/3 standards and is described in Figure 75. For more details, refer to the AN1181 ST7 application note. 15.7.2.3 Designing hardened software to avoid noise problems EMC characterization and optimization are performed at component level with a typical application environment and simplified MCU software. It Electrical Sensitivities
Symbol LU DLU Parameter Static latch-up class Dynamic latch-up class
should be noted that good EMC performance is highly dependent on the user application and the software in particular. Therefore it is recommended that the user applies EMC software optimization and prequalification tests in relation with the EMC level requested for his application. Software recommendations: The software flowchart must include the management of runaway conditions such as: - Corrupted program counter - Unexpected reset - Critical Data corruption (control registers...) Prequalification trials: Most of the common failures (unexpected reset and program counter corruption) can be reproduced by manually forcing a low state on the RESET pin or the Oscillator pins for 1 second. To complete these trials, ESD stress can be applied directly on the device, over the range of specification values. When unexpected behavior is detected, the software can be hardened to prevent unrecoverable errors occurring (see application note AN1015).
Conditions TA=+25C TA=+85C VDD=5.5V, fOSC=4MHz, TA=+25C
Class 1) A A A
Figure 75. Simplified Diagram of the ESD Generator for DLU
RCH=50M RD=330
DISCHARGE TIP
VDD VSS
CS=150pF ESD GENERATOR 2)
HV RELAY
ST7
DISCHARGE RETURN CONNECTION
Notes: 1. Class description: A Class is an STMicroelectronics internal specification. All its limits are higher than the JEDEC specifications, that means when a device belongs to Class A it exceeds the JEDEC standard. B Class strictly covers all the JEDEC criteria (international standard). 2. Schaffner NSG435 with a pointed test finger.
126/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
EMC CHARACTERISTICS (Cont'd) 15.7.3 ESD Pin Protection Strategy To protect an integrated circuit against Electrostatic Discharge the stress must be controlled to prevent degradation or destruction of the circuit elements. The stress generally affects the circuit elements which are connected to the pads but can also affect the internal devices when the supply pads receive the stress. The elements to be protected must not receive excessive current, voltage or heating within their structure. An ESD network combines the different input and output ESD protections. This network works, by allowing safe discharge paths for the pins subjected to ESD stress. Two critical ESD stress cases are presented in Figure 76 and Figure 77 for standard pins and in Figure 78 and Figure 79 for true open drain pins.
Standard Pin Protection To protect the output structure the following elements are added: - A diode to VDD (3a) and a diode from VSS (3b) - A protection device between VDD and VSS (4) To protect the input structure the following elements are added: - A resistor in series with the pad (1) - A diode to VDD (2a) and a diode from VSS (2b) - A protection device between VDD and VSS (4)
Figure 76. Positive Stress on a Standard Pad vs. VSS
VDD VDD
(3a)
(2a) (1) IN
OUT
Main path Path to avoid
(4)
(3b)
(2b)
VSS
VSS
Figure 77. Negative Stress on a Standard Pad vs. VDD
VDD VDD
(3a)
(2a) (1) IN
OUT
Main path
(4)
(3b)
(2b)
VSS
VSS
127/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
EMC CHARACTERISTICS (Cont'd) True Open Drain Pin Protection The centralized protection (4) is not involved in the discharge of the ESD stresses applied to true open drain pads due to the fact that a P-Buffer and diode to VDD are not implemented. An additional local protection between the pad and VSS (5a and 5b) is implemented to completely absorb the positive ESD discharge. Multisupply Configuration When several types of ground (VSS, VSSA, ...) and power supply (VDD, VDDA, ...) are available for any reason (better noise immunity...), the structure shown in Figure 80 is implemented to protect the device against ESD.
Figure 78. Positive Stress on a True Open Drain Pad vs. VSS
VDD
Main path Path to avoid
VDD
OUT
(4)
IN
(1)
(5a)
(3b)
(2b)
(5b)
VSS
VSS
Figure 79. Negative Stress on a True Open Drain Pad vs. VDD
VDD
Main path
VDD
OUT
(4)
IN
(1)
(3b)
(3b)
(2b)
(3b)
VSS
VSS
Figure 80. Multisupply Configuration
VDD VDDA
VDDA
VSS VSSA
BACK TO BACK DIODE BETWEEN GROUNDS
VSSA
128/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.8 I/O PORT PIN CHARACTERISTICS 15.8.1 General Characteristics Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol VIL VIH Vhys IL IS RPU CIO tf(IO)out tr(IO)out tw(IT)in Parameter Input low level voltage
2)
Conditions
Min 0.7xVDD
Typ 1)
Max 0.3xVDD
Unit V mV
Input high level voltage 2) Schmitt trigger voltage hysteresis 3) Input leakage current Static current consumption 4) Weak pull-up equivalent resistor 5) I/O pin capacitance Output high to low level fall time 6) External interrupt pulse time 7) CL = 50pF Output low to high level rise time 6) Between 10% and 90% VSS < VIN < VDD Floating input mode VIN = VSS VDD = 5V VDD = 3.3V
400 1 200 62 170 120 200 5 25 25 1 250 300
A k pF ns tCPU
Figure 81. Two typical Applications with unused I/O Pin
VDD 10k
ST72XXX
10k UNUSED I/O PORT UNUSED I/O PORT
ST72XXX
Figure 82. Typical IPU vs. VDD with VIN=VSS
Ipu [A] 70 60 50 40 30 20 10 0 3.2 3.5 4 Vdd [V] 4.5 5 5.5 Ta=-40C Ta=25C Ta=85C Ta=125C
Notes: 1. Unless otherwise specified, typical data is based on TA = 25C and VDD = 5V. 2. Data based on characterization results, not tested in production. 3. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested. 4. Configuration not recommended, all unused pins must be kept at a fixed voltage: using the output mode of the I/O for example or an external pull-up or pull-down resistor (see Figure 81). Data based on design simulation and/or technology characteristics, not tested in production. 5. The RPU pull-up equivalent resistor is based on a resistive transistor (corresponding IPU current characteristics described in Figure 82). This data is based on characterization results, tested in production at VDD max. 6. Data based on characterization results, not tested in production. 7. To generate an external interrupt, a minimum pulse width has to be applied on an I/O port pin configured as an external interrupt source.
129/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORT PIN CHARACTERISTICS (Cont'd) 15.8.2 Output Driving Current Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol Parameter Output low level voltage for a standard I/O pin when 8 pins are sunk at same time (see Figure 83 and Figure 86) VOL 1) Output low level voltage for a high sink I/O pin when 4 pins are sunk at same time (see Figure 84 and Figure 87) VDD = 5V Conditions IIO=+5mA TA85C TA85C IIO=+2mA TA85C TA85C IIO=+20mA, TA85C TA85C IIO=+8mA TA85C TA85C IIO=-5mA, TA85C VDD-1.6 TA85C VDD-1.7 IIO=-2mA TA85C VDD-0.8 TA85C VDD-1.0 Min Max 1.3 1.5 0.65 0.75 1.5 1.7 0.75 0.85 Unit
V
VOH 2)
Output high level voltage for an I/O pin when 4 pins are sourced at same time (see Figure 85 and Figure 88)
Figure 83. Typical VOL at VDD=5V (standard)
Vol [V] at Vdd=5V 2.5 Ta=-40C 2 1.5 1 0.5 0 0 2 4 Iio [mA] 6 8 10 Ta=25C Ta=125C Ta=85C
Figure 85. Typical VOH at VDD=5V
Voh [V] at Vdd=5V 6 5 4 3 2 1 -8 -6 -4 Iio [mA] -2 0 Ta=-40C Ta=25C Ta=85C Ta=125C
Figure 84. Typical VOL at VDD=5V (high-sink)
Vol [V] at Vdd=5V 2 Ta=-40C 1.5 Ta=25C 1 0.5 0 0 5 10 15 Iio [mA] 20 25 30 Ta=125C Ta=85C
Notes: 1. The IIO current sunk must always respect the absolute maximum rating specified in Section 15.2.2 and the sum of IIO (I/O ports and control pins) must not exceed IVSS. 2. The IIO current sourced must always respect the absolute maximum rating specified in Section 15.2.2 and the sum of IIO (I/O ports and control pins) must not exceed IVDD. True open drain I/O pins does not have VOH.
130/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
I/O PORT PIN CHARACTERISTICS (Cont'd) Figure 86. Typical VOL vs. VDD (standard I/Os)
Vol [V] at Iio=2mA 0.5 0.45 0.4 0.35 0.3 0.25 0.2 3.2 3.5 4 4.5 5 5.5 Vdd [V] Ta=25C Ta=125C Ta=-40C Ta=85C Vol [V] at Iio=5mA 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 3.2 3.5 4 Ta=-40C Ta=25C Ta=85C Ta=125C
4.5 Vdd [V]
5
5.5
Figure 87. Typical VOL vs. VDD (high-sink I/Os)
Vol [V] at Iio=8mA 0.55 0.5 0.45 0.4 0.35 0.3 0.25 0.2 3.2 3.5 4 4.5 5 5.5 Vdd [V] 0.7 0.5 3.2 3.5 4 4.5 5 5.5 Vdd [V] 1.1 0.9 Ta=25C Ta=125C 1.3 Ta=-40C Ta=85C Vol [V] at Iio=20mA 1.5 Ta=25C Ta=125C Ta=-40C Ta=85C
Figure 88. Typical VOH vs. VDD
Voh [V] at Iio=-2mA 5.5 5 4.5 4 3.5 3 2.5 2 3.2 3.5 4 4.5 5 5.5 Vdd [V] Ta=25C Ta=125C 1 0 3.5 4 4.5 Vdd [V] 5 5.5 Ta=-40C Ta=85C 3 2 Ta=-40C Ta=25C Ta=85C Ta=125C Voh [V] at Iio=-5mA 5 4
131/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.9 CONTROL PIN CHARACTERISTICS 15.9.1 Asynchronous RESET Pin Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol VIL VIH Vhys VOL RON Parameter Input low level voltage
2)
Conditions
Min 0.7xVDD
Typ 1)
Max 0.3xVDD
Unit V mV
Input high level voltage 2) Schmitt trigger voltage hysteresis 3) Output low level voltage 4) (see Figure 91, Figure 92) Weak pull-up equivalent resistor 5) VDD=5V VIN=VSS IIO=+5mA IIO=+2mA VDD=5V VDD=3.4V
400 0.68 0.28 20 80 40 100 6 30 20 100 0.95 0.45 60 120
V k 1/fSFOSC s s ns
tw(RSTL)out Generated reset pulse duration th(RSTL)in tg(RSTL)in External reset pulse hold time 6) Filtered glitch duration 7)
External pin or internal reset sources
Figure 89. Typical Application with RESET Pin 8)
ST72XXX
AL
PT
IO
VDD
VDD RON
VDD
N
USER EXTERNAL RESET CIRCUIT 8)
0.1F
4.7k RESET
INTERNAL RESET CONTROL
O
0.1F
WATCHDOG RESET LVD RESET
Notes: 1. Unless otherwise specified, typical data is based on TA=25C and VDD=5V. 2. Data based on characterization results, not tested in production. 3. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested. 4. The IIO current sunk must always respect the absolute maximum rating specified in Section 15.2.2 and the sum of IIO (I/O ports and control pins) must not exceed IVSS. 5. The RON pull-up equivalent resistor is based on a resistive transistor (corresponding ION current characteristics described in Figure 90). This data is based on characterization results, not tested in production. 6. To guarantee the reset of the device, a minimum pulse has to be applied to RESET pin. All short pulses applied on RESET pin with a duration below th(RSTL)in can be ignored. 7. The reset network (the resistor and two capacitors) protects the device against parasitic resets, especially in a noisy environments. 8. The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the device can be damaged when the ST7 generates an internal reset (LVD or watchdog).
132/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CONTROL PIN CHARACTERISTICS (Cont'd) Figure 90. Typical ION vs. VDD with VIN=VSS
Ion [A] 200 150 100 50 0 3.2 3.5 4 4.5 5 5.5 Vdd [V] Ta=-40C Ta=25C Ta=85C Ta=125C
Figure 91. Typical VOL at VDD=5V (RESET)
Vol [V] at Vdd=5V 2 Ta=25C 1.5 1 0.5 0 0 1 2 3 4 Iio [mA] 5 6 7 8 Ta=125C Ta=-40C Ta=85C
Figure 92. Typical VOL vs. VDD (RESET)
Vol [V] at Iio=2mA 0.55 0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 3.2 3.5 4 4.5 5 5.5 Vdd [V] Ta=25C Ta=125C Ta=-40C Ta=85C
Vol [V] at Iio=5mA 1.2 1 0.8 0.6 0.4 3.2 3.5 4
Ta=-40C Ta=25C
Ta=85C Ta=125C
4.5
5
5.5
Vdd [V]
133/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
CONTROL PIN CHARACTERISTICS (Cont'd) 15.9.2 ISPSEL Pin Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol VIL VIH IL Parameter Input low level voltage 1) Input high level voltage 1) Input leakage current Conditions Min VSS VDD-0.1 Max 0.2 12.6 1 Unit V A
VIN=VSS
Figure 93. Two Typical Applications with ISPSEL Pin 2)
ISPSEL
PROGRAMMING TOOL 10k
ISPSEL
ST72XXX
ST72XXX
Notes: 1. Data based on design simulation and/or technology characteristics, not tested in production. 2. When the ISP Remote mode is not required by the application ISPSEL pin must be tied to VSS.
134/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.10 TIMER PERIPHERAL CHARACTERISTICS Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified. 15.10.1 Watchdog Timer
Symbol tw(WDG) Parameter Watchdog time-out duration Conditions Min 12288 fCPU = 8 MHz 1.54 Typ Max 786432 98.3 Unit tCPU ms
Refer to I/O port characteristics for more details on the input/output alternate function characteristics (output compare, input capture, external clock, PWM output...).
15.10.2 16-Bit Timer
Symbol Parameter Conditions Min 1 2 fCPU = 8 MHz 250 0 0 fCPU/4 fCPU/4 16 Typ Max Unit tCPU tCPU ns MHz MHz bit tw(ICAP)in Input capture pulse time tres(PWM) PWM resolution time fEXT fPWM Timer external clock frequency PWM repetition rate
ResPWM PWM resolution
135/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.11 COMMUNICATION INTERFACE CHARACTERISTICS 15.11.1 SPI - Serial Peripheral Interface Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol fSCK 1/tc(SCK) tr(SCK) tf(SCK) tsu(SS) th(SS) tw(SCKH) tw(SCKL) tsu(MI) tsu(SI) th(MI) th(SI) ta(SO) tdis(SO) tv(SO) th(SO) tv(MO) th(MO) Parameter Master SPI clock frequency fCPU = 8 MHz Slave fCPU = 8 MHz SPI clock rise and fall time SS setup time SS hold time SCK high and low time Data input setup time Data input hold time Data output access time Data output disable time Data output valid time Data output hold time Data output valid time Data output hold time Slave Slave Master Slave Master Slave Master Slave Slave Slave Slave (after enable edge) Master (before capture edge) 0 0.25 0.25 tCPU
Refer to I/O port characteristics for more details on the input/output alternate function characteristics (SS, SCK, MOSI, MISO).
Conditions Min fCPU/128 0.0625 0 Max fCPU/4 2 fCPU/2 4 Unit
MHz
see I/O port pin description 120 120 100 90 100 100 100 100 0 120 240 120
ns
Figure 94. SPI Slave Timing Diagram with CPHA = 0 3)
SS INPUT tsu(SS) SCK INPUT CPHA=0 CPOL=0 CPHA=0 CPOL=1 ta(SO) MISO OUTPUT tw(SCKH) tw(SCKL) tv(SO) th(SO) tr(SCK) tf(SCK)
LSB OUT
tc(SCK)
th(SS)
tdis(SO)
see note 2
see note 2
MSB OUT
BIT6 OUT
tsu(SI)
th(SI)
MOSI INPUT
MSB IN
BIT1 IN
LSB IN
Notes: 1. Data based on design simulation and/or characterization results, not tested in production. 2. When no communication is on-going the data output line of the SPI (MOSI in master mode, MISO in slave mode) has its alternate function capability released. In this case, the pin status depends on the I/O port configuration. 3. Measurement points are done at CMOS levels: 0.3xVDD and 0.7xVDD.
136/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
COMMUNICATION INTERFACE CHARACTERISTICS (Cont'd) Figure 95. SPI Slave Timing Diagram with CPHA = 1 1)
SS INPUT tsu(SS) SCK INPUT CPHA=1 CPOL=0 CPHA=1 CPOL=1 ta(SO) tw(SCKH) tw(SCKL) tv(SO) th(SO) tr(SCK) tf(SCK)
LSB OUT
tc(SCK)
th(SS)
tdis(SO)
MISO OUTPUT
see note 2
HZ
MSB OUT
BIT6 OUT
see note 2
tsu(SI)
th(SI)
MOSI INPUT
MSB IN
BIT1 IN
LSB IN
Figure 96. SPI Master Timing Diagram 1)
SS INPUT tc(SCK) CPHA=0 CPOL=0 SCK INPUT CPHA=0 CPOL=1 CPHA=1 CPOL=0 CPHA=1 CPOL=1 tw(SCKH) tw(SCKL) tsu(MI) MISO INPUT tv(MO) th(MI) tr(SCK) tf(SCK)
MSB IN
BIT6 IN
LSB IN
th(MO)
MOSI OUTPUT
see note 2
MSB OUT
BIT6 OUT
LSB OUT
see note 2
Notes: 1. Measurement points are done at CMOS levels: 0.3xVDD and 0.7xVDD. 2. When no communication is on-going the data output line of the SPI (MOSI in master mode, MISO in slave mode) has its alternate function capability released. In this case, the pin status depends of the I/O port configuration.
137/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
COMMUNICATIONS INTERFACE CHARACTERISTICS (Cont'd) 15.11.2 SCI - Serial Communications Interface Subject to general operating condition for VDD, fOSC, and TA unless otherwise specified. Refer to I/O port characteristics for more details on the input/output alternate function characteristics (RDI and TDO).
Conditions Symbol Parameter fCPU Accuracy vs. Standard Prescaler Conventional Mode TR (or RR)=64, PR=13 TR (or RR)=16, PR=13 TR (or RR)= 8, PR=13 TR (or RR)= 4, PR=13 TR (or RR)= 2, PR=13 TR (or RR)= 8, PR= 3 TR (or RR)= 1, PR=13 Extended Mode ETPR (or ERPR) = 13 ~0.79% Extended Mode ETPR (or ERPR) = 35 Standard Baud Rate Unit
fTx fRx
~0.16% Communication frequency 8MHz
300 ~300.48 1200 ~1201.92 2400 ~2403.84 4800 ~4807.69 9600 ~9615.38 10400 ~10416.67 19200 ~19230.77 38400 ~38461.54 14400 ~14285.71
Hz
138/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
15.12 8-BIT ADC CHARACTERISTICS Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.
Symbol fADC VAIN RAIN CADC tSTAB tADC Parameter ADC clock frequency Conversion range voltage 2) VSSA 6 0 fCPU=8MHz, fADC=4MHz
4)
Conditions
Min
Typ 1)
Max 4 VDDA 10 3)
Unit MHz V k pF s 1/fADC
External input resistor Internal sample and hold capacitor Stabilization time after ADC enable Conversion time (Sample+Hold) - Sample capacitor loading time - Hold conversion time
3 4 8
Figure 97. Typical Application with ADC
VDD VT 0.6V RAIN VAIN CIO ~2pF VDD VDDA 0.1F VSSA ST72XXX VT 0.6V IL 1A AINx
ADC
Notes: 1. Unless otherwise specified, typical data is based on TA=25C and VDD-VSS=5V. They are given only as design guidelines and are not tested. 2. When VDDA and VSSA pins are not available on the pinout, the ADC refer to VDD and VSS. 3. Any added external serial resistor will downgrade the ADC accuracy (especially for resistance greater than 10k). Data based on characterization results, not tested in production. 4. The stabilization time of the AD converter is masked by the first tLOAD. The first conversion after the enable is then always valid.
139/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
8-BIT ADC CHARACTERISTICS (Cont'd) ADC Accuracy
Symbol |ET| EO EG |ED| |EL| Parameter Total unadjusted error 1) Offset error
1)
VDD=5V, 2) fCPU=1MHz Typ. Max 2.0 1.5 1.5
VDD=5.0V, 3) fCPU=8MHz Typ. Max 2.0 1.5 1.5 1.5 1.5
VDD=3.3V, 3) fCPU=8MHz Typ Max 2.0 1.5 1.5 1.5 1.5
Unit
Gain Error 1) Differential linearity error Integral linearity error 1)
1)
LSB
1.5 1.5
Figure 98. ADC Accuracy Characteristics
Digital Result ADCDR 255 254 253 1LSB IDEAL V -V DDA SSA = ---------------------------------------256 (2) ET 7 6 5 4 3 2 1 0 1 VSSA 2 3 4 1 LSBIDEAL Vin (LSBIDEAL) 5 6 7 253 254 255 256 VDDA EO EL ED (3) (1) EG (1) Example of an actual transfer curve (2) The ideal transfer curve (3) End point correlation line
ET=Total Unadjusted Error: maximum deviation between the actual and the ideal transfer curves. EO=Offset Error: deviation between the first actual transition and the first ideal one. EG=Gain Error: deviation between the last ideal transition and the last actual one. ED=Differential Linearity Error: maximum deviation between actual steps and the ideal one. EL=Integral Linearity Error: maximum deviation between any actual transition and the end point correlation line.
Notes: 1. ADC Accuracy vs. Negative Injection Current: For IINJ- = 0.8mA, the typical leakage induced inside the die is 1.6A and the effect on the ADC accuracy is a loss of 1 LSB for each 10K increase of the external analog source impedance. This effect on the ADC accuracy has been observed under worst-case conditions for injection: - negative injection - injection to an Input with analog capability, adjacent to the enabled Analog Input - at 5V VDD supply, and worst case temperature. 2. Data based on characterization results with TA = 25C. 3. Data based on characterization results over the whole temperature range.
140/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
16 PACKAGE CHARACTERISTICS
16.1 PACKAGE MECHANICAL DATA Figure 99. 64-Pin Thin Quad Flat Package (14x14)
D D1 A1 A A2
Dim. A A1 A2 0.05 1.35 0.30 0.09 16.00 14.00 16.00 14.00 0.80 0 0.45 3.5 0.60 1.00 7 0 1.40 0.37 mm Min Typ Max 1.60 0.15 0.002 Min inches1) Typ Max 0.063 0.006
1.45 0.053 0.055 0.057 0.45 0.012 0.015 0.018 0.20 0.004 0.630 0.551 0.630 0.551 0.031 3.5 0.039 7 0.75 0.018 0.024 0.030 0.008
b
b c D D1 E E1 e L
e E1 E
L L1 c
L1
Number of Pins N 64 Note 1. Values in inches are converted from mm and rounded to 3 decimal digits.
Figure 100. 44-Pin Thin Quad Flat Package (10x10)
D D1 A1 b A A2
Dim. A A1 A2 b C D D1 E E1 e 0 0.45 L L1 0.05 1.35 0.30 0.09 12.00 10.00 12.00 10.00 0.80 3.5 0.60 1.00 7 0 1.40 0.37 mm Min Typ Max 1.60 0.15 0.002 Min inches1) Typ Max 0.063 0.006
1.45 0.053 0.055 0.057 0.45 0.012 0.015 0.018 0.20 0.004 0.000 0.008 0.472 0.394 0.472 0.394 0.031 3.5 0.039 7 0.75 0.018 0.024 0.030
E1 E
e
L1 L
c
Number of Pins N 44 Note 1. Values in inches are converted from mm and rounded to 3 decimal digits.
141/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
PACKAGE CHARACTERISTICS (Cont'd) 16.2 THERMAL CHARACTERISTICS
Symbol RthJA PD TJmax Ratings Package thermal resistance (junction to ambient) TQFP64 TQFP44 Power dissipation 1) Maximum junction temperature
2)
Value 60 52 500 150
Unit C/W mW C
Notes: 1. The power dissipation is obtained from the formula PD = PINT + PPORT where PINT is the chip internal power (IDD x VDD) and PPORT is the port power dissipation determined by the user. 2. The average chip-junction temperature can be obtained from the formula TJ = TA + PD x RthJA.
16.3 ECOPACK(R) In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK(R) specifications are available at www.st.com.
142/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
17 DEVICE CONFIGURATION AND ORDERING INFORMATION
17.1 INTRODUCTION Each device is available for production in user programmable versions (Flash) as well as in factory coded versions (ROM). EEPROM data memory and Flash devices are shipped to customers with a default content (FFh), while ROM factory coded parts contain the code supplied by the customer. This implies that Flash devices have to be configured by the customer using the Option Bytes while the ROM devices are factory-configured. 17.2 OPTION BYTES The two option bytes allow the hardware configuration of the microcontroller to be selected. The option bytes have no address in the memory map and can be accessed only in programming mode (for example using a standard ST7 programming tool). The default content of the Flash is fixed to FFh. In masked ROM devices, the option bytes are fixed in hardware by the ROM code (see option list). 17.2.1 User Option Byte 0 Bit 7:2 = Reserved, must always be 1. Bit 1 = 64/44 Package Configuration. This option bit allows to configured the device according to the package. 0: 44-pin packages 1: 64-pin packages Bit 0 = FMP Full memory protection. This option bit enables or disables external access to the internal program memory (readout protection). Clearing this bit causes the erasing (by overwriting with the currently latched values) of the whole memory (not including the option bytes). 0: Program memory not readout protected 1: Program memory readout protected Note: The data EEPROM is not protected by this bit in Flash devices. In ROM devices, a protection can be selected in the Option List (see page 145). 17.2.2 User Option Byte 1 Bit 7 = CSS Clock Security System disable This option bit enables or disables the CSS features. 0: CSS enabled 1: CSS disabled Bit 6:4 = OSC[2:0] Oscillator selection These three option bits can be used to select the main oscillator as shown in Table 25. Bit 3:2 = LVD[1:0] Low voltage detection selection These option bits enable the LVD block with a selected threshold as shown in Table 26. Bit 1 = WDG HALT Watchdog Reset on Halt mode This option bit determines if a RESET is generated when entering Halt mode while the Watchdog is active. 0: No Reset generation when entering Halt mode 1: Reset generation when entering Halt mode Bit 0 = WDG SW Hardware or software watchdog This option bit selects the watchdog type. 0: Hardware (watchdog always enabled) 1: Software (watchdog to be enabled by software) Table 25. Main Oscillator Configuration
Selected Oscillator External Clock (Stand-by) ~4 MHz Internal RC 1~14 MHz External RC Low Power Resonator (LP) Medium Power Resonator (MP) Medium Speed Resonator (MS) High Speed Resonator (HS) OSC2 OSC1 OSC0 1 1 1 0 0 0 0 1 1 0 1 1 0 0 1 0 X 1 0 1 0
Table 26. LVD Threshold Configuration
Configuration LVD Off Highest Voltage Threshold (4.50V) Medium Voltage Threshold (4.05V) Lowest Voltage Threshold (3.45V) LVD1 LVD0 1 1 0 0 1 0 1 0
USER OPTION BYTE 0 7 Reserved Default Value 1 1 1 1 1 1 0 7
USER OPTION BYTE 1 0 OSC OSC OSC WDG WDG LVD1 LVD0 2 1 0 HALT SW 1 1 0 1 1 1 1
64/44 FMP CSS X 0 1
143/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
DEVICE CONFIGURATION AND ORDERING INFORMATION (Cont'd) 17.3 TRANSFER OF CUSTOMER CODE Customer code is made up of the ROM contents and the list of the selected options (if any). The ROM contents are to be sent on diskette, or by electronic means, with the hexadecimal file in .S19 format generated by the development tool. All unused bytes must be set to FFh. Figure 101. ROM Factory Coded Device Types The selected options are communicated to STMicroelectronics using the correctly completed OPTION LIST appended. The STMicroelectronics Sales Organization will be pleased to provide detailed information on contractual points.
DEVICE PACKAGE TEMP. RANGE / XXX Code name (defined by STMicroelectronics) A = -40 to +85C B = -40 to +105C C = -40 to +125C T = Plastic TQFP ST72334J2, ST72334J4, ST72334N2, ST72334N4, ST72314J2, ST72314J4, ST72314N2, ST72314N4, ST72124J2
Figure 102. Flash User Programmable Device Types
DEVICE PACKAGE TEMP. RANGE
A = -40 to +85C C = -40 to +125C T = Plastic TQFP ST72C334J2, ST72C334J4, ST72C334N2, ST72C334N4, ST72C314J2, ST72C314J4, ST72C314N2, ST72C314N4, ST72C124J2
144/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
MICROCONTROLLER OPTION LIST Customer: Address: Contact: Phone No: ................................................................................... ................................................................................... ................................................................................... ...................................................................................
Reference/ROM code*:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . *The ROM or FASTROM code name is assigned by STMicroelectronics. ROM or FASTROM code must be sent in .S19 format. .Hex extension cannot be processed. STMicroelectronics references ROM Type/Memory Size/Package (check only one option): ------------------------------------------------------------------------------------------ROM DEVICE: | 8K | 16K ------------------------------------------------------------------------------------------- | TQFP44: | [ ] ST72124J2T | | | [ ] ST72314J2T | [ ] ST72314J4T | | [ ] ST72334J2T | [ ] ST72334J4T | TQFP64: | [ ] ST72314N2T | [ ] ST72314N4T | | [ ] ST72334N2T | [ ] ST72334N4T | ------------------------------------------------------------------------------------------FASTROM DEVICE:| 8K | 16K | ------------------------------------------------------------------------------------------TQFP44: | [ ] ST72P124J2T | | | [ ] ST72P314J2T | [ ] ST72P314J4T | | [ ] ST72P334J2T | [ ] ST72P334J4T | TQFP64: | [ ] ST72P314N2T | [ ] ST72P314N4T | | [ ] ST72P334N2T | [ ] ST72P334N4T | Conditioning: Marking: [ ] Tape and Reel [ ] Standard marking [ ] Tray
[ ] Special marking (ROM only): TQFP (10 char. max) : _ _ _ _ _ _ _ _ _ _ Authorized characters are letters, digits, '.', '-', '/' and spaces only. Please consult your local STMicroelectronics sales office for other marking details if required. Temperature Range: [ ] -40C to +85C Clock Source Selection: Resonator: [ ] -40C to +105C [ ] -40C to +125C
RC Network: External Clock: Clock Security System: LVD Reset:
[ ] LP: Low power resonator (1 to 2 MHz) [ ] MP: Medium power resonator (2 to 4 MHz) [ ] MS: Medium speed resonator (4 to 8 MHz) [ ] HS: High speed resonator (8 to 16 MHz) [ ] Internal [ ] External [] [ ] Disabled [ ] Disabled [ ] Enabled [ ] Enabled: [ ] Highest threshold [ ] Medium threshold [ ] Lowest threshold
Watchdog Selection: Watchdog Reset on Halt: Program Readout Protection: Data EEPROM Readout Protection*: *available on ST72334 only
[ ] Software Activation [ ] Reset [ ] Disabled [ ] Disabled
[ ] Hardware Activation [ ] No reset [ ] Enabled [ ] Enabled
Comments: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply Operating Range in the application:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notes:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signature:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
145/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
17.4 DEVELOPMENT TOOLS STMicroelectronics offers a range of hardware and software development tools for the ST7 microcontroller family. Full details of tools available for the ST7 from third party manufacturers can be obtain from the STMicroelectronics Internet site www.st.com. Tools from these manufacturers include C compliers, emulators and gang programmers. STMicroelectronics Tools Three types of development tool are offered by ST, all of them connect to a PC via a parallel (LPT) port: see Table 27 and Table 28 for more details. Table 27. STMicroelectronics Tool Features
Tool ST7 Development Kit In-Circuit Emulation Programming Capability1) Yes (same features as HDS2 emulator but without Yes (DIP packages only)2) logic analyzer) Yes, powerful emulation No features including trace/ logic analyzer No Yes Software Included ST7 CD ROM with: - ST7 Assembly toolchain - STVD7 and WGDB7 powerful Source Level Debugger for Win 3.1, Win 95 and NT - C compiler demo versions - ST Realizer for Win 3.1 and Win 95 - Windows Programming Tools for Win 3.1, Win 95 and NT
ST7 HDS2 Emulator
ST7 Programming Board
Notes: 1. In-Situ Programming (ISP) interface for Flash devices. 2. Tool equipped with a DIP socket only; an adapter may be required to program devices in TQFP packages.
Table 28. Dedicated STMicroelectronics Development Tools
Supported Products ST72(C)334J2, ST72(C)334J4, ST72(C)334N2, ST72(C)334N4, ST72(C)314J2, ST72(C)314J4, ST72(C)314N2, ST72(C)314N4, ST72(C)124J2 ST7 Development Kit ST7 HDS2 Emulator ST7 Programming Board
ST7MDT2-EPB2/EU ST7MDT2-DVP2 ST7MDT2-EMU2B ST7MDT2-EPB2/US ST7MDT2-EPB2/UK
146/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
DEVELOPMENT TOOLS (Cont'd) 17.4.1 Suggested List of Socket Types Table 29. Suggested List of TQFP64 Socket Types
Package / Probe TQFP64 EMU PROBE ENPLAS YAMAICHI YAMAICHI Adaptor / Socket Reference OTQ-64-0.8-02 IC51-0644-1240.KS-14584 IC149-064-008-S5 Socket type Open Top Clamshell SMC
Table 30. Suggested List of TQFP44 Socket Types
Package / Probe TQFP44 TQFP44 EMU PROBE ENPLAS YAMAICHI YAMAICHI Adaptor / Socket Reference OTQ-44-0.8-04 IC51-0444-467-KS-11787 IC149-044-*52-S5 Socket type Open Top Clamshell SMC
17.5 ST7 APPLICATION NOTES All relevant ST7 application notes can be found on www.st.com.
147/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
18 IMPORTANT NOTES
18.1 SCI BAUD RATE REGISTERS Caution: The SCI baud rate register (SCIBRR) MUST NOT be written to (changed or refreshed) while the transmitter or the receiver is enabled.
148/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
19 SUMMARY OF CHANGES
Description of the changes between the current release of the specification and the previous one.
Date Revision Main changes Initial release of the ST72334xx-Auto,ST72314xx-Auto, ST72124Jx-Auto datasheet This datasheet was created from the ST72334J/N, ST72314J/N, ST72124J datasheet, revision 2.5 dated April 2003, with the following changes: Changed document title and description on page 1 Removed PSDIP package outlines from page 1 "Device Summary" on page 1: - modified to include only automotive devices - replaced `ROM' with `Flash/ROM' as program memory for ST72124J2-Auto device - added operating temperature range specific to ROM devices Section 1 "PREAMBLE: ST72C334-Auto VERSUS ST72E331 SPECIFICATION" on page 7: Replaced ST72C334 with ST72C334-Auto Section 2 "INTRODUCTION" on page 8: Added -Auto extension to ST72xxxJ/N numbers Section 3 "PIN DESCRIPTION" on page 9: Removed Figure "56-Pin SDIP Package Pinout" Figure 3.44-Pin TQFP Package Pinout (J versions): Removed SDIP package pinout Table 1, "Device Pin Description," on page 11: Removed SDIP device pin number columns Section 8 "SUPPLY, RESET AND CLOCK MANAGEMENT" on page 26: Added -Auto extension to ST72xxxJ/N numbers in first paragraph Modified description of external and internal RC in "MULTI-OSCILLATOR (MO)" on page 30 Section 13.1.3 "Functional Description" on page 50: Replaced 500ns with 30s at end of second paragraph to be in line with spec given in Section 15.9.1 "Asynchronous RESET Pin" on page 132 Section 14.1.4 "Indexed (No Offset, Short, Long)" on page 103: Replaced "The indirect addressing mode" with "The indexed addressing mode" in second paragraph Section 15.3.1 "General Operating Conditions" on page 111: Modified ambient temperature range conditions to include only automotive device suffix versions Figure 95.SPI Slave Timing Diagram with CPHA = 1 1): Replaced CPHA=0 with CPHA=1 for SCK INPUT Section 16.1 "PACKAGE MECHANICAL DATA" on page 141: - removed Figure "56-Pin Plastic Dual In-Line Package, Shrink 600-mil Width" - removed Figure "42-Pin Plastic Dual In-Line Package, Shrink 600-mil Width" - added Section 16.3 "ECOPACK(R)" on page 142 - removed Section "SOLDERING AND GLUEABILITY INFORMATION" Section 16.2 "THERMAL CHARACTERISTICS" on page 142: Removed SDIP packages and associated values from package thermal resistance ratings Section 17.2.1 "User Option Byte 0" on page 143: Replaced 56/42-pin package configurations with 64/44-pin package configurations Figure 101.ROM Factory Coded Device Types: Modified to include only automotive devices Figure 102.Flash User Programmable Device Types: - modified to include only automotive devices - removed B temperature version "MICROCONTROLLER OPTION LIST" on page 145: Removed SDIP devices Section 17.4 "DEVELOPMENT TOOLS" on page 146: Replaced `http//mcu.st.com' with `www.st.com" at end of first paragraph Table 27, "STMicroelectronics Tool Features," on page 146: - changed programming capability from `Yes (all packages)' to `Yes' for ST7 Programming Board - added footnote 2 Section 17.5 "ST7 APPLICATION NOTES" on page 147: Removed Table "ST7 Application Notes" Updated disclaimer on last page to include a mention about the use of ST products in automotive applications
17-Oct-2007
1
149/150
ST72334xx-Auto, ST72314xx-Auto, ST72124Jx-Auto
Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
150/150

▲Up To Search▲

Price & Availability of ST7MDT2-DVP2

	To Download ST7MDT2-DVP2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .